Panasonic AG-HPX370P Benutzerhandbuch
16
Chapter
9
Maintenance
and
Inspections
Inspections
Priority
Warning
type
LCD or viewfinder
indication
Tally lamp
Warning
lamp
Alarm
tone
*6
Warning description
and recording/playback
operation
Countermeasures
8
1394
connection
error
connection
error
1394 INITIAL ERROR Blinks
red
red
Blinks 4
times per
second
times per
second
Blinks 4
times per
second
times per
second
No
The DVCPRO/DV cable
has become disconnected
or multiple devices are
connected.
has become disconnected
or multiple devices are
connected.
Check the camera
and device
connections,
reconnect them if
necessary, then turn
the power off and
back on again.
and device
connections,
reconnect them if
necessary, then turn
the power off and
back on again.
9
Battery
nearly empty
nearly empty
The last bar in the battery
level indication blinks (This
indication appears also
when MENU indications
have been turned OFF.)
level indication blinks (This
indication appears also
when MENU indications
have been turned OFF.)
Blinks 1 time
per second
per second
Blinks 1 time
per second
per second
No
The battery is near depletion.
Operation continues.
Operation continues.
*5
Replace the battery
as necessary.
as necessary.
10
P2 card
nearly fully
recorded
nearly fully
recorded
The P2CARD level indicator
blinks.
blinks.
Blinks 1 time
per second
during
recording.
per second
during
recording.
Blinks 1 time
per second
during
recording.
per second
during
recording.
No
Less than 2 minutes is left on
the P2 cards (level indicator
shows 1 minute or less). This
warning appears only during
recording.
the P2 cards (level indicator
shows 1 minute or less). This
warning appears only during
recording.
Replace or insert
additional P2 cards.
additional P2 cards.
*1 P2 SYSTEM ERROR cause indication
• P2 MICON ERROR: The P2 microprocessor does not respond.
• P2 CONTROL ERROR: A P2 recording control error has occurred.
• CAM MICON ERROR: The camera microprocessor does not respond.
• P2 CONTROL ERROR: A P2 recording control error has occurred.
• CAM MICON ERROR: The camera microprocessor does not respond.
*2 REC WARNING cause indication
• CARD ERROR*: P2CARD error (* indicates the number of the slot of the card with the error.) Stops recording.
• REC RAM OVERFLOW: Overflow of recording RAM. Stops recording.
• PULL DOWN ERROR: 24P, 30P (25P) video pulldown error. Recording continues.
• OVER MAX# CLIPS: The limit for the number of clips that can be recorded to one P2 card (up to 1000 clips) has been
• REC RAM OVERFLOW: Overflow of recording RAM. Stops recording.
• PULL DOWN ERROR: 24P, 30P (25P) video pulldown error. Recording continues.
• OVER MAX# CLIPS: The limit for the number of clips that can be recorded to one P2 card (up to 1000 clips) has been
reached.
• ERROR: Other recording errors.
*3 Perform either of the following procedures to cancel this warning.
• Press a playback control button.
• Press the THUMBNAIL button.
• Remove the P2 card and insert another card.
• Press the THUMBNAIL button.
• Remove the P2 card and insert another card.
*4 Perform either of the following procedures to cancel this warning.
• Press the REC button.
• Press a playback control button.
• Press the THUMBNAIL button.
• Remove all cards.
• Press a playback control button.
• Press the THUMBNAIL button.
• Remove all cards.
*5 When NEAR END CANCEL is set to ON, you can press the DISP/MODE CHK button to cancel the alarm.
*6 When the alarm sounds, audio is not output to the camera speakers or earphones. The DISP/MODE CHK button cancels
*6 When the alarm sounds, audio is not output to the camera speakers or earphones. The DISP/MODE CHK button cancels
only the alarm tone when pressed during an alarm.