Panasonic KX-TG2388 Benutzerhandbuch
Answering System Features
52
For assistance, please visit http://www.panasonic.com/consumersupport
Memory capacity
The total recording capacity (including
your greeting message, caller messages
and memo) is about 16 minutes (about 8
minutes in “Enhanced recording mode”,
see page 55). A maximum of 64 messages
(including a greeting message and memo
message) can be recorded.
your greeting message, caller messages
and memo) is about 16 minutes (about 8
minutes in “Enhanced recording mode”,
see page 55). A maximum of 64 messages
(including a greeting message and memo
message) can be recorded.
L
If message memory becomes full:
– E flashes on the base unit.
– the ANSWER ON indicator flashes
– E flashes on the base unit.
– the ANSWER ON indicator flashes
rapidly (if the answering system is
turned on).
turned on).
– the unit announces “Memory full”
when operating the answering system
and recording a memo message.
and recording a memo message.
To record additional messages, erase
unnecessary messages.
unnecessary messages.
L
If less than 3 minutes of recording time is
available, the unit will announce the
remaining recording time when
operating the answering system.
available, the unit will announce the
remaining recording time when
operating the answering system.
L
Messages are retained even if a power
failure occurs. All messages are saved
until you erase them. (Flash memory
message backup)
failure occurs. All messages are saved
until you erase them. (Flash memory
message backup)
L
The total recording capacity may be
reduced by the calling party’s
background noise.
reduced by the calling party’s
background noise.
Note:
L
If message memory becomes full, the
unit will automatically switch to the
“Greeting only” mode. New
messages will not be recorded. If you
have recorded your own greeting
message, that same greeting message
will be announced to callers even though
their messages will not be recorded. If
you have not recorded your own
greeting message, the pre-recorded
message used for “Greeting only”
mode will be announced to callers
(page 47).
unit will automatically switch to the
“Greeting only” mode. New
messages will not be recorded. If you
have recorded your own greeting
message, that same greeting message
will be announced to callers even though
their messages will not be recorded. If
you have not recorded your own
greeting message, the pre-recorded
message used for “Greeting only”
mode will be announced to callers
(page 47).
Remote operation
Using a touch tone phone, you can call
your phone number from outside and
access the unit to listen to messages. The
unit’s voice guidance will prompt you to
press certain dial keys to perform different
operations.
your phone number from outside and
access the unit to listen to messages. The
unit’s voice guidance will prompt you to
press certain dial keys to perform different
operations.
Important:
L
In order to operate the answering
system remotely, you must first set a
remote code (page 54). This code must
be entered each time you operate the
answering system remotely.
system remotely, you must first set a
remote code (page 54). This code must
be entered each time you operate the
answering system remotely.
Using the answering system
remotely
remotely
1
Dial your phone number from a touch
tone phone.
tone phone.
L
If the ring count is set to “Toll
saver” (page 54), the number of
rings you hear will indicate whether or
not you have new messages.
saver” (page 54), the number of
rings you hear will indicate whether or
not you have new messages.
2
After the greeting message starts, enter
your remote code.
your remote code.
L
The unit will announce the number of
new messages, and will play back the
new messages.
new messages, and will play back the
new messages.
3
After 3 seconds, the voice guidance will
start. Follow the voice guidance as
necessary.
start. Follow the voice guidance as
necessary.
4
When finished, hang up.
Note:
L
When you press a key, press firmly.
L
You can hang up at any time.
L
You can ignore the voice guidance and
control the unit using remote
commands.
control the unit using remote
commands.
TG2388.book 52 ページ ２００５年７月１４日 木曜日 午後４時５８分