First Alert FA148CPSSIA Benutzerhandbuch

∗∗∗∗29 COMMUNICATION DEVICE MENU MODE 

This mode is for programming an IP, GSM, or IP/GSM Communicator Module using an alpha keypad. Alternatively, these 
options can be programmed via the AlarmNet Direct website. After programming is complete, the module must be registered 
with AlarmNet before reporting via the communication device can occur. Refer to the device’s instructions for registration 
procedures.  

 

NOTE: The module must be set to device address 3. 

 

IMPORTANT:  The use of an IP/GSM Communicator Module 
requires an AlarmNet–I account. Please obtain the account 
information from the central station prior to programming this 
module.  

 

Using an Alpha Keypad as a 7720P Programming Tool 
When programming with 

∗29 menu mode, the alpha 

keypad mimics the functions of the 7720P Programming 
Tool. See figure to right and table below for 7720P key 
functions. Each key has two possible functions: a normal 
function and a SHIFT function.   

 

  Normal functions: The numeric values labeled directly 

on the keys and the left-hand functions shown in 
diagram on the ABC keys. To perform a normal key 
function, simply press the desired key.  

 

  SHIFT functions: Those functions shown in diagram 

above the numerical keys and the right-hand functions 
shown on the ABC keys. To perform a SHIFT key 
function, press SHIFT key (D key), then press the 
desired function key (shift function is indicated by the lit 
READY LED).  

 

FA560KP-005-V0

SHIFT

FUNCTION

WHEN LIT

ARMED

READY

FA 5 6 0

BYPASS

CHIME

STAY

TEST

CODE

AWAY

OFF

MAX

INSTANT

READY

R

 

 

7720P Emulation Template for Alpha Keypads 

 

∗∗∗∗29 IP/GSM Program Mode 

Press 

∗29 while in Data Field Programming mode. The following prompts appear. 

 

E N A B L E   I P / G S M ?  

0 = N o ,   1 = Y e s  

 

0 = no, not using IP or GSM; 
1 = yes using IP and/or 

GSM module  

[

∗] to continue 

 

[Default = 0 (no IP and/or GSM)] 

If using a communication device, enter 1 at this prompt and 
enter 1-Prog at the next prompt to program and register the 
device. Use the communication device’s Installation Guide for 
details of the device’s programming prompts and instructions for 
registration. 

 

1 = P R O G   2 = D I A G  

0 = Q U I T  

 

1= Prog (program the 

IP/GSM options) 

2 = Diag (enter diagnostic 

mode)   

0 = Quit; returns to data field 

programming mode 

Select whether you want to program the communication device 
or enter the device’s diagnostic mode. 
 
Diagnostic Mode Note: Diagnostic mode option available only 
for communicators with firmware version 2.4.16 or higher. 

 
 

∗∗∗∗29 Menu Mode 

(A) = BS/ESC  [BS]: Press to delete entry 

[ESC]: Press to quit Program Mode 

 

Also, can reset EEPROM defaults † 

 

(B) = 

↓/↑ 

[

↓]: Scroll down programming 

[

↑]: Scroll up programming  

(C) = N/Y 

[N]: Press for "NO" answer 

[Y]: Press SHIFT-Y for "YES" answer 

(D) = SHIFT 

Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a 
key is pressed. Press again for each SHIFT function desired. 

1/A 

[1]: For entering the number 1 

[A]: Used for entering C.S. ID number 

2/B 

[2]: For entering the number 2 

[B]: Used for entering C.S. ID number 

3/C 

[3]: For entering the number 3 

[C]: Used for entering C.S. ID number 

4/D 

[4]: For entering the number 4 

[D]: Used for entering C.S. ID number 

5/E 

[5]: For entering the number 5 

[E]: Used for entering C.S. ID number 

6/F 

[6]: For entering the number 6 

[F]: Used for entering C.S. ID number 

7/S 

[7]: For entering the number 7 

[S]: Press to display diagnostic status 

8/T 

[8]: For entering the number 8 

[T]: Press to send TEST messages 

9/X 

[9]: For entering the number 9 

[X]: Press to reset the IP/GSM  

[

∗] / SPACE 

[

∗]: Used to select programming options 

[SPACE]: Not used 

0 

[0]: For entering the number 0 

 

[#] / ENTER 

[#] / ENTER: Press to accept entries 

No SHIFT function 

 

 

 

† Active only when the "REVIEW?" prompt is displayed