Techko S082X Merkblatt

Seite von 2
SAFETY SECURITY
 
MAGNET GUARD
 
MODEL S082X/S082K
 
S082X
 
S082K
 
 
OPERATION MANUL
3.INSTANT mode.    
    When an entry is detected. The alarm sounds
    immediately. This is used to protect you when you
    are  at home.
4.DELAY mode.  
    This mode is used when you are leaving your home. 
    On your return, an entry alert beep tone will sound
    to alert you to disarm the unit. If the unit is not 
    disarmed within10 seconds of entry, the alarm will 
    sound a110db (S082KA is 115db) alarm siren.
5.The 110db/115db alarm will sound for about 30/36 
    seconds, while the alarm is sounding or during the 
    entry alert time the security code can be entered to
    disarm the unit.
6.To disarm the unit, enter the security code followed by
    the
 #ON/OFF
button.
C H I M E  M O D E
1 . B e f o r e  a c t i v a t i n g  t h e  c h i m e ,  s l i d e  t h e  f u n c t i o n  s w i t c h 
        t o  t h e
C H I M E
p o s i t i o n .
2 . E n t e r  t h e  s e c u r i t y  c o d e  f o l l o w e d  b y  t h e
# O N / O F F
b u t t o n .
3 . T h e
A R M
L E D  w i l l  i l l u m i n a t e  t o  v e r i f y  t h e  u n i t  i s  O N , 
        f o l l o w e d  b y  a  s h o r t  b e e p .  I f  t h e A R M  l i g h t  d o e s  n o t         
        i l l u m i n a t e  t h i s  i n d i c a t e d  t h e  u n i t  i s  O F F.
4 . T h e  c h i m e  w i l l  s o u n d  i f  t h e r e  i s  a n  e n t r y.  T h e  c h i m e  w i l l 
        s o u n d  f o r  e a c h  e n t r y  u n t i l  t h e  u n i t  i s  t u r n e d  O F F ( d i s a r m e d )
N O T E :  T h e  p o s i t i o n  o f  t h e  f u n c t i o n  s w i t c h  d o e s  n o t
n e c e s s a r i l y  i n d i c a t e  t h e  m o d e  t h e  u n i t  i s  i n 
( C H I M E  /  I N S TA N T  /  D E L AY ) .  E a c h  t i m e  b e f o r e 
a c t i v a t i n g  t h e  u n i t ,  s e t  t h e  f u n c t i o n  s w i t c h  t o  t h e  c o r r e c t 
p o s i t i o n  f o r  t h e  m o d e  d e s i r e d .           
  PANIC ALARM
T h e  r e d
PA N I C
b u t t o n  o n  t h e  f r o n t  p a n e l  a c t i v a t e s  t h e
  a l a r m  d u r i n g  a  p o s s i b l e  e m e r g e n c y.
1 . P r e s s  t h e  p a n i c  b u t t o n . T h i s  w i l l  a c t i v a t e  t h e  11 0 d b
      ( S 0 8 2 K A  i s  11 5 d b )  a l a r m  s i r e n .
2 . D i s a r m  t h e  PA N I C  a l a r m ,  f o l l o w  t h e  s a m e  p r o c e d u r e  a s
        y o u  w o u l d  t o  D I S A R M  t h e  u n i t . 
CAUTION
THE MAGNET GUARD IS EXTREMELY LOUD. FOR YOUR
SAFETY. NEVER PLACE THE UNIT CLOSE TO YOUR EARS. 
TO TEST THE ALARM, DIRECT THE UNIT AWAY FROM YOU 
AT ARMS LENGTH AND ACTIVATE.  
 
PATENT PENDING NOTICE
THIS PRODUCT IS PROTECTED UNDER FEDERAL PATENT. TRADEMARK AND COPYRIGHT
LAWS AND LAWS PREVENTING UNFAIR COMPETITION. NO DUPLICATION OR SIMULATION OF  
THIS PRODUCT IS PERMITTED EXCEPT BY WRITTEN AUTHORIZATION OF TECHKO, INC.  
TECHKO AND THE CONFIGURATION OF THIS PRODUCT ARE TRADEMARKS OF TECHKO, INC. 
COPYRIGHT 1992 TECHKO, INC. ALL RIGHTS RESERVED  
 
 
ALARM OUTPUT AND
PANIC BUTTON TEST
To test the alarm output, press the PANIC button located on
front of the unit. (THIS UNIT IS VERY LOUD, COVER THE 
SIREN ON THE FRONT OF THE UNIT BEFORE ACTIVATING).
The unit will immediately sound a piercing alarm siren. To
disarm the unit, enter your security code followed by the
#ON/OFF
button. (If you have not entered a security code
the default is 0
and S082K is 5
  
  
  
 
CHIME TESTING
1.Set the function switch to the CHIME
position.
2.Enter the security code followed by the
#ON/OFF
button,
    the
ALARM
LED will illuminate. If this does not happen 
    repeat steps 1 and 2.
3.Close the door and then open it again, a pleasant chime will
    sound 3 times.
4.To disarm the unit, enter the security code followed by the 
   
#ON/OFF
button.
5.As long as the unit is in the
ARM
mode, the chime will   
   continue to sound until
DISARMED
 
  
ALARM TESTING
1.Set the function switch to the INSTANT or
DELAY
    position.
2. Enter the security code followed by the
#ON/OFF
button, 
    the
ARM
LED will turn on. If this does not happen, repeat 
   steps 1 and 2.
3. Close the door and open it again in INSTANT mode, the 
    alarm sounds immediately. If the alarm is in DELAY mode,  
    the alarm will emit a low beep tone to alert your to disarm the  
    unit, if not disarmed, the unit will then sound a piercing alarm.
4.To disarm the unit, enter the security code followed by the 
   
#ON/OFF
button.  
  
   
  Note: in both modes, CHIME or ALARM (instant / delay) the unit will continue to  
  sound until DISARMED . The unit will only sound the ALARM if ARMED in
  the ALARM mode. If armed in the CHIME mode the unit will sound only the CHIME. 
  If function switch is changed after the unit has been activated, this will not alter the 
  sound being produced.   
ALARM MODE
1.Before arming the unit slide the function switch to the 
  
INSTANT/DELAY
position.
2.To arm the S082X / S082K, enter the security code
    followed by the #ON/OFF
 button, the  ARM  LED will 
    turn on. If this does not happen repeat steps 1 and 2.
      
TESTING
OPERATION
1
2
3
4
5
6
7
8
9
*
0
#
S082KA
1  
2  
3
4  
5
*  
#
PANIC
S082X
TEMPLATE
SCREW HOLE
SCREW HOLE
MODE S082KA
SCREW HOLE
Customer Service : 
1-888-8TECHKO (1-888-883-2456)
Website: www.techkomaid.com
Mfg. By
9767 Research Drive
Irvine, CA 92618-4626
MADE IN CHINA