Ameriphone AM-7000 Merkblatt

©AMERIPHONE       4/02  

∆

M07898   5220-1001

3

The AM-SX uses an infrared sensor to monitor the

area. When you turn on the AM-SX you have a

60 second set up period to leave the area. After

the one minute set up period, any motion in the

monitored area will trigger the sensor and a sig-

nal will be sent 15 seconds later to activate the

AM-6000 or the AM-7000 system. The red indi-

cator light will come on when a signal is being

sent to the AM-6000 or AM-7000. Upon returning

to the area being monitored, you will have 15

seconds to turn off the switch to avoid triggering

the unit. Caution: Small animals walking in the

monitored area may trigger activation.
Battery and Operation Tests

Install the 

9V alkaline 

battery as shown.

Check the battery strength every six months, or

sooner, by moving in front of the unit to activate

the system. If the red indicator light doesn’t come

on after 60 seconds, replace with new battery.

Position the AM-SX within 80 feet from the

Alertmaster AM-6000 or AM-7000 and its

receivers. For optimal room coverage, install

the AM-SX on a wall, on a shelf or table edge,

at a height not to exceed six feet. It will moni-

tor an area approximately 15 feet in width, up

to a distance of 15 feet in front of the unit.

Do not place the unit directly facing a window

to avoid false triggering by some one walking 

outside the window.

The Alertmaster System uses special radio sig-

nals to communicate between the base unit and

all its accessories. For the Motion Sensor AM-SX

to activate the base unit, it has to be on the

same “channel.”  A “Dip switch” is used for

channel selection. 
Your system and all the accessories have been

preset in the factory to a standard channel

setting.  Under normal operating conditions,

there is no adjustment necessary.
If your system encounters interference and

repeatedly activates by itself for no obvious rea-

sons, it may be triggered by a system nearby in

your neighborhood.
If interference from another Alertmaster

Notification System or other wireless signals is

present, change channel switch settings on all

components.

1.Unplug AC cord and locate Dip 

switch on the underside of the 

AM-6000 console and the back of 

the AM-7000.

2.Change the switch setting by sliding 

all individual switches to a new 

position as shown.

3.Slide open battery door of AM-SX, 

locate dip switch, change switch 

setting to exactly match new settings 

on console. 

4.Change the switch settings on each 

of your other accessories (doorbell, 

Remote Receiver, etc.) to match the 

new switch settings in the console. 

All settings must be identical for the 

system to work.

1 2

 3

 4

Use a pen

or pencil to

set DIP

switches to

match

exactly as

shown

AM-6000 or

AM-7000

Battery

Door

AM-SX

If any problem should occur during operation of

your Alertmaster Model AM-SX accessor

y, review

the “Symptom and Remedy

” list in your

Alertmaster Model AM-6000 or AM-7000

Operating Instructions.  Make sure no part of the

Alertmaster Notification System is on or near

metal surfaces or electronic equipment.  Should

the difficulty persist, contact Ameriphone or your

authorized dealer for assistance.

The Alertmaster Model AM-SX uses an FCC

approved transmitter, and complies with Par

t 15

of the FCC Rules. Its operation is subject to the

following two conditions: 

1. This device may not cause harmful inter

ference.

2. This device must accept any interference that 

may be received, including interference that may 

cause undesired operation.

Ameriphone warrants the AM-SX against any defect in workmanship or material, for

a period of one year from the date of purchase.

If the product is defective and returned within 30 days of purchase, the unit will be

replaced at the place of purchase at no charge.

If it is returned after 30 days but within one year

, Ameriphone will repair or replace

it at no charge. In repairing your AM-SX, we may use new or reconditioned parts. If

we elect to replace your AM-SX, we may replace it with a new or reconditioned

product of the same or similar design. Repair or replacement will be warranted for

either 90 days or the remaining time on the warranty period, whichever is longer.

When in need of warranty repair, please call our customer ser

vice department at

(800) 874-3005 (voice), (800) 772-2889 (TTY). They will help you process your

return shipment. Y

ou must prepay all shipping costs.

Implied warranties, including those of fitness for a particular purpose and mer-

chantability (unwritten warranty that the product is fit for ordinary use), are limited to

one year from date of purchase. We will not pay for loss of time, inconvenience, loss

of use of your AM-SX or property damage caused by your AM-SX or its failure to

work, or any other incidental or  consequential damages. Some states do not allow

limitations on how long an implied warranty lasts or the exclusion of incidental or

consequential damages, so the above exclusions or imitations may not apply to you.

We suggest you save the original package materials in the event that you need to

ship your AM-SX back. When shipping for warranty repair, include your name,

address, phone number, proof of date of purchase and a description of the problem.

After repairing the product, we will ship it back to you at no cost within the United

States.

This warranty does not cover defects resulting from accidents, damage while in tran-

sit to our service location, alterations, unauthorized repair

, failure to follow instruc-

tions, misuse, use outside the United States or Canada, fire, flood and acts of God.

➡

12082 Wester

n Avenue, Garden Grove, CA 92841

VOICE (800) 874-3005  TTY (800) 772-2889

FAX (714) 897-4703  

ameriphonecs@plantronics.com   www.ameriphone.com

Works with ALER

TMASTER  Product Series

®

®