Wayne-Dalton 8000 Benutzerhandbuch
4
Locate the auto latch striker plates over the pre-punched holes in the
vertical track nearest the center of the lock section. Fasten the striker
plates to the vertical track using (2) 1/4” - 20 x 9/16” track bolts and
flanged hex nuts. Align the auto latch flippers such that the arm will
engage the striker plates. Position the auto latch flipper 1/8” from the
edge of the section and secure it to the section with (3) 1/4” - 20 x
11/16” self drilling screws (WOOD DOORS will use 1/4” - 14 x 1” lag
screws). Bend the bottom edge of the auto latch flipper arm away
from the door slightly for smoother operation. Feed one end of the lock
cable through the slotted hole of an auto latch flipper and secure with
(1) 1/4” - 20 x 9/16” track bolt. Pull the cable taut, but not enough
to lift the flipper out of the striker plate. While holding taut, feed the
lock cable through the slotted hole of the remaining auto latch flipper,
secure with (1) 1/4” - 20 x 9/16” track bolt and flanged hex nut,
vertical track nearest the center of the lock section. Fasten the striker
plates to the vertical track using (2) 1/4” - 20 x 9/16” track bolts and
flanged hex nuts. Align the auto latch flippers such that the arm will
engage the striker plates. Position the auto latch flipper 1/8” from the
edge of the section and secure it to the section with (3) 1/4” - 20 x
11/16” self drilling screws (WOOD DOORS will use 1/4” - 14 x 1” lag
screws). Bend the bottom edge of the auto latch flipper arm away
from the door slightly for smoother operation. Feed one end of the lock
cable through the slotted hole of an auto latch flipper and secure with
(1) 1/4” - 20 x 9/16” track bolt. Pull the cable taut, but not enough
to lift the flipper out of the striker plate. While holding taut, feed the
lock cable through the slotted hole of the remaining auto latch flipper,
secure with (1) 1/4” - 20 x 9/16” track bolt and flanged hex nut,
(SEE
FIG. 9-10).
NOTE: Ensure that the bolt is through the front of the flippers and the
nut is on the back of the flippers with cable going through the front of
the flippers.
nut is on the back of the flippers with cable going through the front of
the flippers.
Operate the lock several times to make sure the auto latch flippers
clear the striker plates when the handle is turned and the flippers en-
gage the striker plates when the handle is released. Adjust the cables
if necessary. Trim off the excess cable with wire cutters after the lock
is operating satisfactorily.
clear the striker plates when the handle is turned and the flippers en-
gage the striker plates when the handle is released. Adjust the cables
if necessary. Trim off the excess cable with wire cutters after the lock
is operating satisfactorily.
STEP 4: Installing The Auto Latch
Rim
cylinder
Trim ring
Lock
plate
Night
latch
(4) #8 x 1/2”
Pan head
screws
(2) 1/4” - 20 x 1-3/4”
Self tapping screws
Extruded holes
in release disk
Inside
handle
“Slide” of
night latch
“Notch” of
release disk
Inside handle
Vertical
track
Auto latch
flippers
Auto latch
flipper
Track
Striker plate
Use pliers to
bend lock arm
slightly
1/4-20 x 11/16”
Self drilling screws
1/4-20 Flanged hex nuts
1/4-20 x 9/16”
Track bolt
Lock
cable
Striker plates
FIG. 8
Center stile
(2) #12 Pan
head screws
FIG. 9
FIG. 10
1/8” Offset from
edge of door