Shark S3501CO Benutzerhandbuch
TOLL FREE:
1-800-798-7398
www.sharkcompany.com
PREPARE
5
For your comfort, you can adjust
the height of the mop. Just lift the
latch on the tube 90 degrees to the
open position. Holding the handle,
extend the tube to the height that’s
right for you and then close latch
to locked position.
latch on the tube 90 degrees to the
open position. Holding the handle,
extend the tube to the height that’s
right for you and then close latch
to locked position.
6
Plug in mop and wait 30 seconds
or less for the mop to heat up.
Pump the handle of the mop by
pushing downward about 10 to 12
times to create steam.
Pump the handle of the mop by
pushing downward about 10 to 12
times to create steam.
NOTE:
Steam is created
automatically when you start
mopping.
mopping.
FILL
4
Lay the mop on the floor or on
a counter top and remove the
water tank cap by turning counter
clockwise. Fill the water tank using
the filling flask. Do not overfill the
water tank. Replace the water cap
and tighten.
water tank cap by turning counter
clockwise. Fill the water tank using
the filling flask. Do not overfill the
water tank. Replace the water cap
and tighten.
IMPORTANT:
Make sure your floors
are sealed. Before using the Steam
Mop consult page 4 for more
information.
Mop consult page 4 for more
information.
DIRT CAN’T HIDE ON
EITHER SIDE! All new
design allows for optimal
cleaning! When one side
of the pocket gets dirty,
just turn the mop head
over and clean with the
other side of the pocket.
EITHER SIDE! All new
design allows for optimal
cleaning! When one side
of the pocket gets dirty,
just turn the mop head
over and clean with the
other side of the pocket.
5
Quick Start
2
4
6
Quick S
tart
When assembling your steam mop
there may be a little water in or around
the water tank. This is because we test
all our steam mops 100% before you
buy them, so you get a quality
Shark
there may be a little water in or around
the water tank. This is because we test
all our steam mops 100% before you
buy them, so you get a quality
Shark
®
Steam Mop.
QUICK TIP:
For easier
pushing
and pulling,
extend the
handle length.
For easier
pushing
and pulling,
extend the
handle length.
ASSEMBLE
1
Insert the mop handle into the
pump actuator (the tube that leads
to the tank). Push the mop handle
and pump actuator together in
until you hear it click into place.
to the tank). Push the mop handle
and pump actuator together in
until you hear it click into place.
2
Select a mop head and cleaning
pad. Choose from the Rectangle,
Triangle or XL Rectangle mop
head. Fit one side of the pocket
onto the head first, then using
the lavender loop, pull the pocket
over the head. Attach the quick
fasteners on the top of the pocket
to secure in place.
Triangle or XL Rectangle mop
head. Fit one side of the pocket
onto the head first, then using
the lavender loop, pull the pocket
over the head. Attach the quick
fasteners on the top of the pocket
to secure in place.
3
Snap the mop head into the base to
secure it. Press the release button
to exchange mop heads.
to exchange mop heads.
QUICK TIPS: We’ve added
an additional mop head.
You can now choose from a
Rectangle mop head for all
the rooms in your house or
the Triangle mop head that
is perfect for bathrooms
and tight spaces or the
XL Rectangle mop head
for big jobs.
an additional mop head.
You can now choose from a
Rectangle mop head for all
the rooms in your house or
the Triangle mop head that
is perfect for bathrooms
and tight spaces or the
XL Rectangle mop head
for big jobs.
NOTE: Do not leave your
Steam Mop unattended
during use.
Steam Mop unattended
during use.
IMPORTANT: Never leave
the steam mop in one spot
for any period of time with
a damp or wet micro-fiber
pocket attached as this will
damage your floors.
the steam mop in one spot
for any period of time with
a damp or wet micro-fiber
pocket attached as this will
damage your floors.
1
3