Manualsbrain.com
  1. Handbücher
  2. Marken
  3. Wayne-Dalton
  4. 9100
  5. Benutzerhandbuch

Wayne-Dalton 9100 Benutzerhandbuch

Download
Seite von 40
6
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your 
local yellow pages/business listings or go to the 
Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
Preparing the opening
WEATHER SEAL
HEADROOM
bACkROOM
DOOR
WIDTH
DOOR HEIGHT
LEVEL HEADER
PLUMb jAMbS
HEADER bOARD 
2” X 6” LUMbER 
PREfERRED
SUITAbLE MOUNTING 
SURfACE 2” X 6” 
LUMbER MINIMUM
P1
Recommended 
tools from 
page 5
HEADER
jAMb
jAMb
heaDRoom 
RequiRemeNT
DooR 
heighT
TRack
maNual 
liFT
moToR 
oPeRaTeD
6’5”
10”, 12”, 14” Radius
89”
125”
6’5”
Low Headroom
101”
125”
6’6”
10”, 12”, 14” Radius
90”
125”
6’6”
Low Headroom
102”
125”
7’0”
10”, 12”, 14” Radius
96”
125”
7’0”
Low Headroom
108”
125”
7’6”
10”, 12”, 14” Radius
102”
137”
7’6”
Low Headroom
114”
137”
8’0” 
10”, 12”, 14” Radius
108”
137”
8’0”
Low Headroom
120”
137”
backRoom RequiRemeNT
TRack 
TyPe
ToRquemaSTeR
® 
PluS
10”, 12”
10”
14”
12”
LHR kit
6 1/2”
fAILURE TO 
SECURELY ATTACH A 
SUITAbLE MOUNTING PAD TO STRUCTURALLY 
SOUND fRAMING COULD CAUSE SPRINGS TO 
VIOLENTLY PULL MOUNTING PAD fROM WALL, 
RESULTING IN SEVERE OR fATAL INjURY.
If you just removed your existing door or you are installing a new 
door, complete all steps in PREPARING THE OPENING. 
To ensure secure mounting of track brackets, side and center 
brackets, or steel angles to new or retro-fit construction, it is 
recommended to follow the procedures outlined in DASMA Technical 
Data Sheets #156, #161 and #164 at www.dasma.com.
The inside perimeter of your garage door opening should be framed 
with wood jamb and header material. The jambs and header must 
be securely fastened to sound framing members. It is recommended 
that 2” x 6” lumber be used. The jambs must be plumb and the 
header level. The jambs should extend a minimum of 12” (305 mm) 
above the top of the opening for TorqueMaster
®
 Plus counterbalance 
systems. for low headroom applications, the jambs should extend 
to the ceiling height. Minimum side clearance required, from the 
opening to the wall, is 3-1/2” (89 mm).
imPoRTaNT: Closely inspect jambs, header and mounting surface. 
Any wood found not to be sound, must be replaced.
for TorqueMaster
®
 Plus counterbalance systems, a suitable 
mounting surface (2” x 4”) must be firmly attached to the wall, 
above the header at the center of the opening.  
NoTe: Drill a 3/16” pilot hole in the mounting surface to avoid 
splitting the lumber. Do not attach the mounting surface with nails.
weather Seal (may Not be included): 
Cut or trim the weather seal (if necessary) to the header and jambs. 
For quick install track: Align the header seal with the inside edge 
of the header and temporarily secure it to the header with equally 
spaced nails. Next, fit the jamb seals up tight against the header 
seal and flush with the inside edge of the jamb. Temporarily secure 
the jamb seals with equally spaced nails. This will keep the bottom 
section from falling out of the opening during installation. Space 
nails approximately 12” apart.
NoTe: Do not permanently attach weather seal to the jamb at this 
time.
heaDRoom RequiRemeNT: Headroom is defined as the space 
needed above the top of the door for tracks, springs, etc. to allow the 
door to open properly. If the door is to be motor operated, 2-1/2” (64 
mm) of additional headroom is required.
NoTe: 6” LHR Conversion kit is available for 12” Radius only. 
Contact your local Wayne-Dalton dealer.
backRoom RequiRemeNT: backroom is defined as the distance 
needed from the opening back into the garage to allow the door to 
open fully.
waRNiNg
jAMb
WEATHER 
SEAL