Lightolier 1104FESR Merkblatt
Instruction Sheet Number
1104FES
Page of 2
Installation Procedure for Convertible IC/Non IC Frame-In-Kits
Lightolier
a Genlyte company
www.lightolier.com
63 Airport Road, Fall River, MA 02720 • (508) 679-83 • Fax (508) 674-470
We reserve the right to change details of design, materials and finish.
© 2005 Genlyte Group LLC • C205
We reserve the right to change details of design, materials and finish.
© 2005 Genlyte Group LLC • C205
Read and understand these instructions before installing fixture.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and
regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
Warranty information on back – retain this sheet.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and
regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
Warranty information on back – retain this sheet.
hINGEd
KNoCK ouT
TAb
T-bAR
hINGEd bAR ENdS
ChANNEL
bENd AT hoLE
TAb
bENd TAb To LoCK
Installation Procedure for Convertible IC/Non IC
Frame-In-Kits 1104F13ES/18ES/26ES and 1004F13ES/18ES/26ES
Frame-In-Kits 1104F13RES/18RES/26RES and 1004F13RES/18RES/26RES
04 Series FIK use 00 Series Trims (Finishing Sections) only
004 Series FIK use 000 Series Trims (Finishing Sections) only
004 Series FIK use 000 Series Trims (Finishing Sections) only
1. Frame-In (Fig. A)
Locate fixture along joist and line up bottom edge of hinged mounting bar
Locate fixture along joist and line up bottom edge of hinged mounting bar
with the bottom of joist and fasten in place.
New Construction
Fig. A
Frame-In
Frame-In
Fig. F
Push-Up
Push-Up
Fig. E
Snap-On
Snap-On
Fig. D
Close-In
Close-In
Fig. C
Swing-Up
Swing-Up
Fig. B
Wire-In
Wire-In
For suspended ceilings:
• Rotate hINGEd bAR ENdS to position shown below and fully extend bars.
• Crimp bottom of edge of ChANNEL to prevent rotation of hINGEd
• Rotate hINGEd bAR ENdS to position shown below and fully extend bars.
• Crimp bottom of edge of ChANNEL to prevent rotation of hINGEd
bAR ENdS.
• bend NoN-hINGEd end of mounting bar at featured hole location and
extend out.
• Position notched area of MouNTING bARS onto T-bAR and lock by bending
TAb underneath T-bAR bEAd as shown.
3”
004IC
3
3
/
4
” 04IC
5
/
4
” 004IC
6
/
4
” 04IC
2. Wire-In (Fig. B)
open hinged J-box CovER fully to its locked position (lift slightly to unlock).
open hinged J-box CovER fully to its locked position (lift slightly to unlock).
open hinged KNoCK ouT to allow NoN-METALLIC CAbLE to enter
JuNCTIoN box. Push CAbLE through CLAMP.
Note: Wiring and connections must not be placed in JuNCTIoN box in a
manner which will interfere with the CLAMPS action to provide strain relief.
Wire to SuPPLy LEAdS. WhITE FIxTuRE LEAd to NEuTRAL SuPPLy LEAd.
bLACK FIxTuRE LEAd to hoT (20v) SuPPLy LEAd. bARE FIxTuRE WIRE to
SuPPLy GRouNd. use wirenuts (local hardware item). Place all electrical
connections in the J-box and close the J-box cover.
SuPPLy GRouNd. use wirenuts (local hardware item). Place all electrical
connections in the J-box and close the J-box cover.
3. Swing-Up (Fig. C)
Extend MouNTING bAR to reach opposite joist and fasten in place. Adjust
Extend MouNTING bAR to reach opposite joist and fasten in place. Adjust
to desired position along MouNTING bAR and lock in place.
hinged Mounting bar
J-box CovER
NoN-METALLIC
ShEAThEd CAbLE
(2 oR 4
GAuGE oNLy)
CAbLE
CLAMP
JuNCTIoN box