Lightolier IS:F302IC Merkblatt

INSTRUCTION SHEET

12-01/Rev-02

ISF:302IC

WITH VAPOUR BARRIER COVER: NºVBE300 (Order separately)

1. Select a location for the fixture.

2. Fasten the edge of the vapour barrier cover under the

wood joist. (Fig.1)

3. Install the fixture (see step A, B and C).

4. Install the ceiling vapour barrier. (Fig.1)

Note: Seal the edges of the vapour barrier cover and the

vapour barrier. (Fig.2)

FOR NEW CEILING:

A. MOUNTING BAR:

Note-1: The mounting bars are extensible from 12½" to 29" max.

Note-2: For off-centre installation, use 20" expandable mounting bars

(Nº1964, order separately).

1. Insert the mounting bars into the proper openings on the short side or the

long side of the mounting frame. (Fig.4)

2. Align the mounting bar with the bottom edge of the joist. (Fig.3)

3. Push in the built-in nailer. (Fig.3)

B. MOUNTING FRAME:

1. Install the locking clip. (Fig.5)

Note-1: The locking clip is also available separately

(Nº0098, order separately).

Note-2: To lock more securely into place fold the locking tabs. (Fig.4)

C. WIRE-IN:

1. Remove the appropriate "Pry-out plug".

2. Insert the supply lead into the junction box:

a) If using FLEXIBLE CONDUIT: Use a BX connector (not provided).

b) If using FLEX WIRE: Insert under the wire connector. (Fig.6)

3. Connect the ground lead. (Fig.7,8)

4. Connect the white leads (NEUTRAL) together, and the black leads

(120V) together. (Fig.7.8)

D. CEILING:

1. Cut a hole in the ceiling (3-3/4 for Model 302 or 4-3/4 for

Model 402), using the mounting frame as a template (if applicable).

(Fig.9)

2. Use the screws to adjust the housing height. Note: Ensure

that the housing is level with the ceiling. (Fig.10)

3. Tighten the screws when completed. (Fig.10)

CAUTION: The lampholder must not be used for temporary lighting,

a protective glass is required for the lamp.

TRIM:

Install the trim using the appropriate sheet.

F. TRANSFORMER / REPLACEMENT:

Note: Before performing maintenance on the transformer, make sure that the

electrical supply to the fixture is turned off.

1. Remove the housing and the two screws located inside. (Fig.10)

2. Push down on the spring tab and release the plate. (Fig.11, 12)

3. Remove the plate from the ceiling, disconnect the wiring , and change the

transformer. (Fig.12)

4. Complete the connections following the wiring diagram (fig.7). Reinstall the

plate onto the spring. (Fig.12)

5. Replace the housing into position. (Fig.10)

INSTALLATION INSTRUCTIONS FOR MOUNTING FRAME

FOR INSULATED CEILING

FIG.3

FIG.4

FIG.5

FIG.6

MOUNTING

FRAME

MOUNTING

BAR

LOCKING

TABS

MOUNTING

BAR

LOCKING

CLIP

MOUNTING

FRAME

"PRY-OUT"

PLUG

FLEXIBLE

WIRE

CONNECTOR

JUNCTION

B O X

WOOD JOIST

FIG.1

FIG.2

VAPOUR

BARRIER EXTENDER

VAPOUR BARRIER

EXTENDER

VAPOUR BARRIER

SILICONE

SEALER

OR OTHER

FIXTURE

FIG.7

(MR)

INPUT

(120V)

NEUTRAL (white)
GROUND

THERMAL

PROTECTOR

LAMP

LOW VOLTAGE

TANSFORMER

JUNCTION

B O X

WHITE

BALCK

MOUNTING

BAR

BUILT-IN

NAILER

WOOD

JOIST

FIG.9

FIG.10

HOUSING

THERMAL

PROTECTOR

LAMP

INPUT

(120V)

NEUTRAL (white)
GROUND

WHITE

BLACK

JUNCTION

B O X

FIG.8

(ES)

302ESIC

302MRIC / 402MRIC

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with National Electrical Code or Canadian Electrical

Code (as applicable) and local regulations. To ensure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

SCREWS

FIG.11

FIG.12

T A B

PLATE

SPRING