Tascam SN29401376 Benutzerhandbuch

■

■

■

■

■

■

■

Make sure that all video connecting plugs are pushed 
in all the way.

Make sure that each video component is properly 
connected.

14, 15

If your TV is connected to HDMI OUT, select 
“- - - - -” in the “HDMI Input” setup to watch 
composite video, and component video sources.

If the video source is connected to a component video 
input, you must assign that input to an input selector, 
and your TV must be connected to either HDMI OUT 
or COMPONENT VIDEO OUT.

15, 49

If the video source is connected to a composite video 
input, you must assign that input to an input selector, 
and your TV must be connected to HDMI OUT or the 
corresponding composite video output.

15, 49

If the video source is connected to an HDMI input, 
you must assign that input to an input selector, and 
your TV must be connected to HDMI OUT.

14, 48

(European models) While the Pure Audio listening 
mode is selected, the analog video circuitry is turned 
off and only video signals input through HDMI IN 
can be output.

On your TV, make sure that the video input to which 
the AV receiver is connected is selected.

—

Reliable operation with an HDMI-to-DVI adapter is 
not guaranteed. In addition, video signals from a PC 
are not guaranteed.

When the resolution is set to any resolution not 
supported by the TV, no video is output from the 
HDMI outputs. 

If the message “Resolution Error” appears on the 
AV receiver’s display, this indicates that your TV 
does not support the current video resolution and you 
need to select another resolution on your DVD 
player.

—

On your TV, make sure that the video input to which 
the AV receiver is connected is selected.

—

When the AV receiver is not connected to a TV via 
HDMI OUT, on-screen menus are not displayed.

—

Depending on the input signal, the on-screen display 
may not appear when the input signal from HDMI IN 
is output to a device connected to HDMI OUT.

Relocate your antenna.

—

Move the AV receiver away from your TV or 
computer.

—

Listen to the station in mono.

When listening to an AM station, operating the 
remote controller may cause noise.

—

Passing cars and airplanes can cause interference.

—

Concrete walls weaken radio signals.

—

If nothing improves the reception, install an outdoor 
antenna.

—

Before operating this unit, be sure to press 
RECEIVER.

—

Make sure that the batteries are installed with the 
correct polarity.

Install new batteries. Don’t mix different types of 
batteries, or old and new batteries.

Make sure that the remote controller is not too far 
away from the AV receiver, and that there’s no 
obstruction between the remote controller and the AV 
receiver’s remote control sensor.

Make sure that the AV receiver is not subjected to 
direct sunshine or inverter-type fluorescent lights. 
Relocate if necessary.

—

If the AV receiver is installed in a rack or cabinet 
with colored-glass doors, the remote controller may 
not work reliably when the doors are closed.

—

Make sure you’ve selected the correct remote 
controller mode.

10, 71

When using the remote controller to control other 
manufacturers’ AV components, some buttons may 
not work as expected.

—

Make sure you’ve entered the correct remote control 
code.

Make sure to set the same ID on both the AV receiver 
and remote controller.

If it’s an 

u-capable component, make sure that the 

u cable and analog audio cable are connected 
properly. Connecting only an 

u cable won’t be 

enough.

Make sure you’ve selected the correct remote 
controller mode.

10, 71

If you’ve connected an cassette tape deck to the 
TV/CD IN jack, or an RI Dock to the TV/CD IN or 
GAME IN jacks, for the remote controller to work 
properly, you must set the input display 
appropriately.

If you cannot operate it, you will need to enter the 
appropriate remote control code.

To control another manufacturer’s component, point 
the remote controller at that component.

To control a component that’s connected via 

u, 

point the remote controller at the AV receiver. Be 
sure to enter the appropriate remote control code first.

The entered remote control code may not be correct. 
If more than one code is listed, try each one.

—