Euro-Pro UV209B Benutzerhandbuch

Important:

If the suction opening in the unit, the hose or the extension tube become 
blocked, switch off the vacuum cleaner and remove the blocking 
substance before you start the unit again.

Warning: To reduce the risk of electric 

shock, the power cord must be 

disconnected before removing the dust 

cup, HEPA filter,changing the filters or 

performing maintenance/trouble shooting 

checks.

5.

When pulling out the power plug 
from the wall outlet, pull the plug 
not the power cord.

1.

Do not operate the vacuum 
cleaner to close too heaters, 
or radiators.

1. Turn unit “Off” and unplug from wall 

outlet.

2. With a flat head screw driver, snap 

off the lens cover by pressing down 

on the two notches on the lens 

cover. (Fig. 23)

3. Lift off the head light lens.

4. Remove the light bulb by pulling it 

out carefully.

5. Replace the new bulb by pushing 

it in.

6. Replace the head light lens by 

pushing it in so that it snaps back in 

place.

6.

Do not pick up anything that is 
burning or smoking such as 
cigarettes, matches or hot ashes.

This appliance was inspected thoroughly and was in good operating condition when it 

was shipped from the factory. If a minor problem occurs, it usually can be solved quite 

easily when the cause is found. Therefore, this checklist is provided for your 

convenience.

2.

Before inserting the power plug 
into the wall outlet, make sure that 
your hands are dry.

7.

Do not run appliance over power 
cord.

9

Cleaner Won’t 

Run 

1.  Not properly plugged into wall 

outlet. 

2.  No electricity in wall outlet. 
3.  On/Off switch not turned on. 
4.  Motor thermostat tripped. 
5. Blown 

fuse/tripped 

breaker. 

1. 

Plug in firmly. 

2. 

Check fuse or breaker. 

3. 

Push on/off switch to on 

4. 

Reset motor thermostat.  

        (page 8 ) 
5. 

Reset circuit breaker or replace fuse. 

Cleaner Won't 

Pick Up 

1.  Full or clogged dust cup. 
2.  Wrong pile height setting. 
3. Clogged 

nozzle. 

4.  Clogged dust inlet port. 
5. Clogged 

hose. 

6. Broken 

belt. 

7.  Hose not inserted fully. 
8. Dirty 

filters. 

1. 

Clean dust cup. (page 5) 

2. 

Adjust setting. (page 5) 

3. Remove 

obstruction. 

4. 

Remove power head cover and 
remove obstruction. 

5. Remove 

obstruction. 

6. 

Replace belt. (page 8) 

7. 

Push hose in securely. 

8. 

Clean / change filters.  

        (page 6, 7) 

Cleaner Picks Up 

Moveable Rugs 

Or Pushes Too 

Hard 

1.  Wrong pile height setting. 

1. 

Adjust setting. (page 5) 

Agitator Does Not 

Turn 

1. Broken 

belt. 

2. Belt 

installed 

incorrectly. 

1. 

Replace belt. (page 8) 

2. 

Check belt changing and agitator 
cleaning. (page 9) 

Air Flow 

Restricted With 

Attachment Use 

Sound Changes 

1. 

Attachment use restricts air 
flow. 

2. New 

carpet 

debris 

clogging 

air path. 

1. 

Check attachment.  

2. Remove 

obstruction. 

3.

Do not vacuum any liquids.

8.

Do not use without dust cup 
filter or filters in place.

9.

Before you start vacuuming, 
make sure to remove large or 
sharp objects that might 
damage the vacuum.

4.

Keep hair, loose clothing, fingers, 

feet and all parts of body away from 
openings, rotating agitator and other 
moving parts. 

2