3M G5 Benutzerhandbuch

Seite von 77
 
Operation 
 
 3M™ Drive-Thru Systems Model G5 and Model XT-1 
Operating Instructions 
November 6 2014 – Revision 2.1 
Page 41 of 77 
Indicator Light Modes 
Use the table below to understand the meaning of the indicator light on the 
headset: 
Indicator 
Mode  Description 
Off  (no  light) 
I ndic ates power  is off .  It will t urn  off  automatically  if  it fails  to 
register  within two  minutes or  if  the battery dies.  
Solid Green 
Headset  is  signed  on,  standby, Lane 1. 
Solid Amber 
Headset  is  signed  on,  standby, Lane 2. 
Solid Red 
Headset  is  in transmit  mode. 
Flashing G reen 
(c hanged f rom  flashing  amber) 
Headset  has  not regist ered, but f ound  an open base  to  whic h it will 
t ry  to  register. 
Flashing G reen 
(immediately aft er  power  on) 
Headset  is  registered  but  has not yet synchronized  or signed on to 
t he base st ation. 
Flashing Amber 
Headset  is  not  regist ered and has  not  found a base  st at ion. 
Steadily  Flashing Red 
Headset  is  the act ive order taker, but  the outbound  talk t o 
c ustomer  is  muted. 
Single Red Flas h 
(c hanged f rom  flashing  green) 
Headset  has  successfully synchronized and signed on with  a base 
s tation (“Lane  1” or “Lane 2”  will also be heard  in the earpiece). 
Alternat ing Flas hing Green and Amber 
Page Monitor Mode.  
Red  – O range – Red –  Green - 
Red  – O range – Red –  Green.. 
Headset  registered t o f our base stations.  
 
Perform the  following proc edure t o clear the headset  regist ration 
dat a: 
1.   Start  wit h t he  Headset  powered  on.   
       It does not have to be in sync wit h any 
       Bas e St ation. 
2.   Press and HOLD t he power  button. 
3.   Press and release t he T1 butt on 2  times. 
4.   Press and release t he T2 butt on 2  times. 
5.   Release t he  power  but ton. 
The  Headset  LED will  illuminate to  solid red f or 2 seconds  and 
t hen it  has  been cleared. 
Red  +  4sec blank + 
Red  +  4sec blank…….. 
The  Base St ation you are trying to regist er your  headset t o,  has 
more than 20 headsets  registered  already 
Follow the st eps  below  to  remove any  registered  heads ets t hat  are 
not  in use  any  more. 
1. Log into the  Base St ation 
2. Press the  Mode  key t ill you see t he System  
     Menu 
3. Select  04 Regis tration 
4. Select  02 Remove Headsets. 
3. Scroll  to  the number of t he  headset you  
     want  to  un-regist er. 
4. Press Enter. 
 
 
Fitting the Headset 
Make the following adjustments to the headset to make it comfortable, less 
likely to fall off and easy for you to hear and speak clearly: 
1.
 
Rotate the ear cup and ear pad so that the indicator on the ear cup is 
aligned to the back of your head.