Sony PDW-R1 Benutzerhandbuch

C

h

ap
te

r 2

 N
a

m

e

s

 a

n

d

 F

u

nc
ti

on
s

 of

 P

a

rt

s

15

2-2 Control Panel

speed varies in the range ±1 times normal speed, according 
to the rotation rate of the jog dial. There are no detents.
Normally, you press the JOG button before turning the jog 
dial, but it is also possible to make a setting to enable jog 
mode directly by turning the dial (set extended menu item 
101 “SELECTION FOR SEARCH DIAL ENABLE” to 
“dial”).

e Shuttle dial
Turn this for playback in shuttle mode. Turn clockwise for 
forward direction playback, and counterclockwise for 
reverse direction playback. In shuttle mode, the playback 
speed varies in the range ±20 times normal speed (using 
MPEG IMX/DVCAM), according to the angular position 
of the shuttle dial. The shuttle dial has a detent at the center 
position, for still image playback.
Normally, you press the SHUTTLE button before turning 
the shuttle dial, but it is also possible to make a setting to 
enable shuttle mode directly by turning the dial (set 
extended menu item 101 “SELECTION FOR SEARCH 
DIAL ENABLE” to “dial”).

When extended menu item 101 “SELECTION FOR 
SEARCH DIAL ENABLE” is set to “dial,” after using the 
shuttle dial, return it to the center position. If the shuttle 
dial is not in the center position, it is possible occasionally 
for vibration from other operations to activate the dial, and 
start playback in shuttle mode.

4 Audio settings section

a VARIABLE (audio level adjustment selector) 

This selects which of the input audio and playback audio 
has the level adjusted by the ALL/CH-1, and CH-2 to CH-
4 adjustment knobs.
REC: Adjust the input audio levels. The playback audio 

levels are fixed at their preset values.

PRESET: Do not adjust the audio levels.
PB: Adjust the playback audio levels. The input audio 

levels are fixed at their preset values.

b ALL/CH-1, CH-2 to CH-4 (audio level) adjustment 

Depending on the setting of the VARIABLE switch, these 
adjust the input audio or playback audio levels of channels 
1 to 4.
By the setting of extended menu item 131 “AUDIO 
VOLUME,” you can enable the ALL/CH-1 knob to 
simultaneously adjust all eight channels. When this 
simultaneous adjustment is enabled the ALL indicator 
lights.

c AUDIO METER SEL (selection) button
When using MPEG IMX format in eight-channel mode, 
select whether the audio level meters should display 
channels 1 to 4 or channels 5 to 8.
Pressing this button toggles the selection, and the audio 
level meter channel display also changes.
The factory default is for channels 1 to 4 to be selected.

d AUDIO MONITOR SEL (selection) button
This button selects two channels from among the up to 
eight audio signal channels. You can monitor the audio of 
the selected channels (the left and right channels in the 
case of stereo output) with the PHONES jack on the front 
panel and the built-in speaker.
Pressing this button cycles through the following five 
channel combinations.
• tr1/2: Channels 1 (left) and 2 (right)
• tr3/4: Channels 3 (left) and 4 (right)
• tr5/6: Channels 5 (left) and 6 (right)
• tr7/8: Channels 7 (left) and 8 (right)
• MENU: Audio channels selected with extended menu 

item 837 and 838 “AUDIO MONITOR CHANNEL 
ARRANGE”

The factory default is for channels 1 (left) and 2 (right) to 
be selected.
You can select whether to monitor both of the selected 
channels or only one, by pressing this button with the 
SHIFT button held down. Each press selects stereo, right, 
or left.
ST: Stereo audio is output from the PHONES jack. 

Monaural audio, the left and right channels mixed, is 
output from the built-in speaker.

R: The right channel audio is output from the PHONES 

jack and the built-in speaker.

L: The left channel audio is output from the PHONES jack 

and the built-in speaker.

1

  VARIABLE switch

ALL indicator

2

 ALL/CH1, CH-2 to CH4 

adjustment knobs

3

 AUDIO METER SEL button

4

 AUDIO MONITOR SEL button