Technicolor - Thomson CDP-CX57 Benutzerhandbuch
– 53 –
• MAIN BOARD IC501 CXP84340-071Q (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1 to 5
A3 to A7
O
6
A12
O
7
A14
O
Address signal output to the static RAM (IC502)
8 to 11
A11 to A8
O
12
A13
O
13
WE
O
Data write enable signal output to the static RAM (IC502) “L” active
14
LDIN
O
Loading motor drive signal (load-in direction) output to the BA6780 (IC601) “H” active
15
LDOUT
O
Loading motor drive signal (load-out direction) output to the BA6780 (IC601) “H” active
16
TBLL
O
Table motor drive signal (counterclockwise) output to the BA6780 (IC601) “H” active
17
TBLR
O
Table motor drive signal (clockwise) output to the BA6780 (IC601) “H” active
18, 19
NC
O
Not used (open)
20
HHOUT
O
AND output of T.SENS1 (pin ^™) and T.SENS2 (pin ^£) when the test mode
21
LEDL
O
Serial data latch pulse output to the LED driver (IC903) “H” active
22
FLLT
O
Serial data latch pulse output to the FL driver (IC901) “L” active
23
JOG1
I
Jog dial pulse input from the rotary encoder (RE901)
24
JOG2
I
Jog dial pulse input from the rotary encoder (RE901)
25
DOORSW
I
Door open/close detect switch (S925) input “L”: close, “H”: open
26
FLCK
O
Serial data transfer clock signal output to the FL driver (IC901) “L” active
27
FLDT
O
Serial data output to the FL driver (IC901)
28
ZMUTE
O
Muting on/off control signal output for the 2nd CD IN “H” active
29
ICSW
O
Enable signal output to the LA5602 (IC201) Used for the BD section reset “H” active
30
RESET
I
System reset signal input from the reset signal generator (IC203) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (10 MHz)
32
XTAL
O
Main system clock output terminal (10 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open)
35
TEX
I
Sub system clock input terminal Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage (+5V) input terminal (for A/D converter)
38
KEY0
I
Key input terminal (A/D input) CLEAR, CHECK, FADER, MEMO SEARCH, INPUT,
TIME/TEXT keys input (S901 to 906)
TIME/TEXT keys input (S901 to 906)
39
KEY1
I
Key input terminal (A/D input)
±, ≠, p, P, ·, PLUS ONE, REPEAT, PLAY MODE keys input (S907 to 914)
±, ≠, p, P, ·, PLUS ONE, REPEAT, PLAY MODE keys input (S907 to 914)
40
KEY2
I
Key input terminal (A/D input)
I/
I/
u, X-FADE, NO DELAY, MEGA CONTROL keys input (S921 to 924)
41
KEY3
I
Key input terminal (A/D input) GROUP 5 to 1, GROUP FILE keys input (S915 to 920)
42
D.SENS
I
Inputs the disc sensor (Q51) detection signal “H” active
43
CD1/2/3
I
COMMAND MODE switch (S701) input terminal
“L”: CD1, “H”: CD3 (CD2: center voltage input)
“L”: CD1, “H”: CD3 (CD2: center voltage input)
44
TEST
I
Setting terminal for the test mode “L”: ADJ mode, center voltage: AFADJ mode
45
BUSOUT
O
Sircs remote control signal output for the S-LINK CONTROL A1 “H” active
46
BUSIN
I
Sircs remote control signal input for the S-LINK CONTROL A1 “L” active
47
SL+
O
Sled feeding signal (external direction) output to the RF amplifier (IC101) “H” active
48
CQCK
O
Command serial clock signal output to the RF amplifier (IC101) and DSP (IC102)
“L” active
“L” active