Ingersoll-Rand 66615X-X-C Benutzerhandbuch

2010

CCN 81660219

(800) 276-4658

FAX (800) 266-7016

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET -- BRYAN, OHIO 43506

OPERATOR’S MANUAL

66615X-X-C

RELEASED:

5-31-88

REVISED:

12-1-10

(REV.

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1-1/2” DIAPHRAGM PUMP

1:1 RATIO (METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to the Model Description Chart to match the pump material op-

tions.

637118-C for air section repair (see page 6).
637124-XX for fluid section repair (see page 4).
637155 Abrasion Resistant Conversion Kit is available for use in heavy

and abrasive material applications (see page 4).

PUMP DATA

Models

see “Model Description Chart” for “-XXX”

. . . . . . . . . . . .

Pump Type

Metallic Air Operated Double Diaphragm

. . . . . . . . .

Material

see “Model Description Chart”

. . . . . . . . . . . .

Weight

Aluminum

51.54 lbs (23.4 kgs)

. . . .

. . . . . . . . . . .

Cast Iron

79.54 lbs (36.1 kgs)

. . . . . . . . . . . .

Stainless Steel

84.54 lbs (38.3 kgs)

. . . . . . . .

[add 23 lbs (10.4 kgs) for cast iron air motor section]

Maximum Air Inlet Pressure

120 p.s.i. (8.3 bar)

. . . . . . . .

Maximum Material Inlet Pressure

10 p.s.i. (0.69 bar)

. . . .

Maximum Outlet Pressure

120 p.s.i. (8.3 bar)

. . . . . . . . .

Maximum Flow Rate

(flooded inlet)

90 g.p.m. (340.7 l.p.m.)

. . . .

Displacement / Cycle @ 100 p.s.i.g.

0.64 gal. (2.42 lit.)

. .

Maximum Particle Size

1/4” dia. (6.4 mm)

. . . . . . . . . . .

Maximum Temperature Limits (diaphragm / ball / seat material)

Acetal

_ to 180_ F (-12_ to 82_ C)

. . . . . . . . . . . . . . . . .

E.P.R.

-60

_ to 280_ F (-51_ to 138_ C)

. . . . . . . . . . . . . . . . .

Hytrel

-20

_ to 150_ F (-29_ to 66_ C)

. . . . . . . . . . . . . . .

Kynar

R PVDF

_ to 200_ F (-12_ to 93_ C)

. . . . . . . . . . .

Neoprene

_ to 200_ F (-18_ to 93_ C)

. . . . . . . . . . . . . .

Nitrile

_ to 180_ F (-12_ to 82_ C)

. . . . . . . . . . . . . . . . .

Polypropylene

_ to 175_ F (2_ to 79_ C)

. . . . . . . . . . .

Polyurethane

_ to 150_ F (-12_ to 66_ C)

. . . . . . . . . . . .

PTFE

_ to 225_ F (4_ to 107_ C)

. . . . . . . . . . . . . . . . .

Santoprene

-40

_ to 225_ F (-40_ to 107_ C)

. . . . . . . . . . .

Viton

-40

_ to 350_ F (-40_ to 177_ C)

. . . . . . . . . . . . . . . .

Dimensional Data

see page 8

. . . . . . . . . . . . . . .

Noise Level @ 70 p.s.i. - 60 c.p.m.

77.7 dba(A)

. .

Tested with 93139 muffler assembly installed.
The pump sound pressure levels published here have been updated to an Equivalent

Continuous Sound Level (L

Aeq

) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-

ROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart. However, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.

66615X-XXX-C

1-1/2” DIAPHRAGM PUMP

Figure 1

MODEL DESCRIPTION CHART

6661 X X - X X X - C

6661XX - X X X - C

637124 - X X

Diaphragm

Ball

FLUID SECTION SERVICE KIT SELECTION

EXAMPLE: MODEL # 666150-361-C
FLUID SECTION SERVICE KIT # 637124-61

Seat Material
1 - Aluminum

4 - Kynar PVDF

2 - 316 Stainless Steel

5 - Carbon Steel

3 - Polypropylene

8 - 440 Stainless Steel

Diaphragm Material
1 - Neoprene

5 - E.P.R.

2 - Nitrile

9 - Hytrel

3 - Viton

B - Santoprene

4 - PTFE / Santoprene

Center Body Material, Threads
5 - Aluminum, N.P.T.F.

7 - Aluminum, BSP

6 - Cast Iron, N.P.T.F.

8 - Cast Iron, BSP

Fluid Cap / Manifold Material, Hardware

(Steel Hardware)

(Stainless Steel Hardware)

0 - Aluminum

A - Aluminum

1 - Stainless Steel

B - Stainless Steel

2 - Cast Iron

C - Cast Iron

Ball Material
1 - Neoprene

6 - Acetal

2 - Nitrile

8 - Polyurethane

3 - Viton

A - Stainless Steel

4 - PTFE

C - Hytrel

5 - E.P.R.

E - Santoprene