Ingersoll-Rand 651616-X Benutzerhandbuch

OPERATOR’S MANUAL

651616-X

RELEASED:

6-6-02

REVISED: 3-4-10

(REV. L)

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

TWO POST LIFT / RAM

For use with 5 - 55 Gallon Drums

(67081 BASIC LIFT / RAM PLUS FOLLOWER PLATE)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

INCLUDE MANUALS: 66516-X FOLLOWER PLATE (PN 97999-854), 67195-X FOLLOWER PLATE (PN 97999-841) &

S-635 GENERAL INFORMATION (PN 97999-635)

THIS MANUAL COVERS THE FOLLOWING MODELS (COMPLETE FOLLOWER DATA ON PAGE 3)

MODEL

(See Page 3 for Follower Plate)

TYPICAL PUMP APPLICATION

651616-1, -2, -3, -7, -8, -9, -13, -14, -15, -19, -51, -52, -53, -57, -58, -59, -63

3-1/4’’ TO 6’’ AIR MOTORS (TIE ROD PUMPS)

651616-4, -5, -6, -10, -11, -12, -16, -17, -18, -20, -54, -55, -56, -60, -61, -62, -64

8’’ TO 12’’ AIR MOTORS (TIE ROD PUMPS)

SERVICE KITS

116772 for repair of E512LM valve.

104302 for repair of R37121-100 miniature regulator.

GENERAL DESCRIPTION

The ARO Model 651616-X Two Post Lift / Ram uses two 3-1/2’’ air-pow-

ered cylinders connected by tubular steel cross member and is welded

to a heavy gauge base plate. It is normally used to raise and lower a fluid

handling pump and follower in and out of a standard 55 - gallon drum, or

when used as a ram it can force high viscosity flowable material into the

pump inlet. It is offered with several follower plate options (see page 4)

which will accommodate most of the ARO Fluid Handling Industrial

pumps and allow connection directly to the pump lower end. There are

also mounting locations on the horizontal beam for the vertical rods al-

lowing use with 5 - gallon containers. Pump air controls (F-R-L) can be

mounted on the top horizontal support beam using the holes provided.

Cast aluminum followers are fitted with a dual lip seal or dual ‘‘O” ring

seal to wipe the drum clean and seal off the material from the atmo-

sphere. Several material options are available for the follower plate out-

er seal. Select a compatible seal for the material being pumped. The

model chart above shows the pump motors they will generally accom-

modate.

When properly secured, this unit has the ability to raise a pump to clear a

standard 55 -gallon drum. The operator is then able to easily remove the

pump from the drum.

This Lift / Ram uses a hand lever 4-way control valve which controls the

air necessary to raise and lower the lift. This unit includes an auxiliary

manual air valve which is used to supply a controlled amount of air pres-

sure to the bottom of the follower plate. When the control valve is in the

‘‘UP’’ position, a small amount of air pressure applied under the follower

plate will help to raise the follower plate, pump and lift by relieving the

vacuum (refer to page 5).

Refer to page 2 for optional accessories available for pump stabilization

and drum hold down.

651616-1

TWO POST LIFT / RAM

BASE DIMENSIONS: 39-1/2’’

(1003.3 mm)

x 24’’

(609.6 mm)

HEIGHT: LOWERED 61-17/32’’

(156.3 cm)

, RAISED: 99-5/32’’

(251.9 cm)

FIGURE 1

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 495-0276 FAX(800) 892-6276

www.ingersollrandproducts.com

CCN 99445348