Yamaha RX-V561 Benutzerhandbuch
35
En
Playback
English
BA
S
IC
OPERA
T
ION
■ Selecting the night listening mode
The night listening modes are designed to improve
listenability at lower volumes or at night.
listenability at lower volumes or at night.
1
Press D
AMP and then press LNIGHT
repeatedly to select “NIGHT:CINEMA” or
“NIGHT:MUSIC”.
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” to reduce the dynamic
“NIGHT:MUSIC”.
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” to reduce the dynamic
range of film soundtracks and make dialog easier to
hear at lower volumes.
hear at lower volumes.
• Select “NIGHT:MUSIC” to preserve ease-of-
listening for all sounds.
• Select “OFF” if you do not want to use this feature.
y
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
2
Press Gl / h to adjust the effect level while
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
displayed in the front panel display.
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
displayed in the front panel display.
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
y
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently.
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently.
• You cannot use the night listening modes in the following cases:
– when the DIRECT STEREO mode (see page 34) is selected.
– when the component connected to the MULTI CH INPUT
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source.
– when headphones are connected to the PHONES jack.
– when the sound field program is selected while you enjoy
– when the sound field program is selected while you enjoy
music contents in a USB memory device etc.
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
■ Displaying signal information
You can display the format, sampling frequency, channel,
bit rate and flag data of the current input signal.
bit rate and flag data of the current input signal.
1
Press D
AMP and then press QMENU on
the remote control.
The top “SET MENU” display appears in the OSD.
The top “SET MENU” display appears in the OSD.
2
Press Gn repeatedly to select “SIGNAL
INFO” and then press G
INFO” and then press G
ENTER.
The following information about the input source
appears in the OSD.
appears in the OSD.
y
The information indicated by the cursor is also displayed in
the front panel display.
The information indicated by the cursor is also displayed in
the front panel display.
3
Press Q
MENU again to exit from “SET
MENU”.
Notes
Display
Description
FORMAT
Signal format.
SAMPLING
The number of samples per second taken
from a continuous signal to make a
discrete signal.
from a continuous signal to make a
discrete signal.
CHANNEL
The number of source channels in the
input signal (front/surround/LFE).
input signal (front/surround/LFE).
BITRATE
The number of bits passing a given point
per second.
per second.
FLAG
Flag data encoded in DTS, Dolby Digital,
or PCM signals that cue this unit to
automatically switch decoders.
or PCM signals that cue this unit to
automatically switch decoders.
SET MENU
TOP MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
[ ]/[ ]:Up/Down
[ENTER]:Enter
[ENTER]:Enter
p
p
;SIGNAL INFO
. FORMAT
DolbyD
SAMPLING
48kHz
CHANNEL
3/2/0.1
BITRATE
384kbps
FLAG
None
[RETURN]:Exit