ONKYO TX-L55 Benutzerhandbuch
29
Connecting AV Components
—Continued
With
(Remote Interactive) you can control your
-compatible Onkyo DVD player with the TX-L55’s
remote controller, and use the following special
functions:
Auto Power On/Standby
When you start playback on the DVD player, if the
TX-L55 is in Standby, it will turn on and select the DVD
player as the input source automatically. Similarly, when
the TX-L55 is set to Standby, the DVD player will also
enter Standby.
TX-L55 is in Standby, it will turn on and select the DVD
player as the input source automatically. Similarly, when
the TX-L55 is set to Standby, the DVD player will also
enter Standby.
Direct Change
When playback is started on the DVD player, the
TX-L55 will automatically select it as the input source.
TX-L55 will automatically select it as the input source.
Notes:
• Push plugs in all the way to make good connections.
• Use only
• Use only
cables for
connections. An
cable is supplied with each
-compatible Onkyo
DVD player.
• Some DVD players have two
sockets, you can
connect either one to the TX-L55. The other is for con-
necting additional
necting additional
-compatible components.
• Connect the TX-L55’s
socket to only an Onkyo
DVD player. Connecting to other manufacturer’s com-
ponents may cause them to malfunction.
ponents may cause them to malfunction.
• Some DVD players may not support all
functions.
Refer to the manual supplied with your DVD player.
Notes:
• Before connecting the power cord, connect all of
• Before connecting the power cord, connect all of
your speakers and AV components.
• Turning on the TX-L55 may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the TX-L55 into a different branch circuit.
equipment on the same circuit. If this is a problem,
plug the TX-L55 into a different branch circuit.
Connecting an Onkyo DVD Player
with
with
To use
, you must make an analog audio
connection (RCA) between the TX-L55 and the
other component, even if they are connected
digitally.
other component, even if they are connected
digitally.
REMOTE
CONTROL
DVD player
Connecting the Power Cord
Turning On the TX-L55
Press the [STANDBY/ON] button.
Alternatively, press the remote
controller’s REMOTE MODE
[AMP] button followed by the
[ON] button.
Alternatively, press the remote
controller’s REMOTE MODE
[AMP] button followed by the
[ON] button.
The TX-L55 comes on, the display
lights up, and the STANDBY indicator
goes off.
lights up, and the STANDBY indicator
goes off.
To turn on a DVD player that’s con-
nected via
nected via
, press the [ON] button
again.
To turn off the TX-L55, press the
[STANDBY/ON] button. The TX-L55
will enter Standby mode. To prevent
any loud surprises the next time you
turn on your TX-L55, always turn down
the volume before turning it off.
[STANDBY/ON] button. The TX-L55
will enter Standby mode. To prevent
any loud surprises the next time you
turn on your TX-L55, always turn down
the volume before turning it off.
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
--/---
INPUT
I
+
-
DVD
TV
AMP
TV
AUX
TUN
DVD
V1
INPUT SELECTOR
V2
TONE
REMOTE
MODE
TUNER
ON
STANDBY
T V
TV CH
T V VOL
+
_
STANDBY/ON
AMP
STANDBY
ON
ON
STANDBY
Remote
controller
TX-L55_En.book Page 29 Tuesday, June 1, 2004 9:02 AM