ONKYO TXNR727 Benutzerhandbuch
Advanced Operations
En-53
*3
“Dynamic EQ” and “Dynamic Volume” cannot be
selected when any of the THX listening modes is
selected, with “Loudness Plus” set to “On” or “Preserve
THX Settings” set to “Yes” (
selected when any of the THX listening modes is
selected, with “Loudness Plus” set to “On” or “Preserve
THX Settings” set to “Yes” (
*4
• When the “Monitor Out” setting is set to “Sub”, “Video”
cannot be selected (
• This setting cannot be used with the NET, USB and
BLUETOOTH input selectors.
*5
Only when you have selected “Custom” in the “Picture
Mode” (
Mode” (
), pressing ENTER allows you to
adjust the following items via the Quick Setup:
“Brightness”, “Contrast”, “Hue” and “Saturation”. Press
RETURN to return to the “Picture Mode” setting.
“Brightness”, “Contrast”, “Hue” and “Saturation”. Press
RETURN to return to the “Picture Mode” setting.
*6
Depending on the input source and listening mode, not
all channels shown here output the sound.
all channels shown here output the sound.
*7
• This setting is not available in either of the following
cases:
– The “Audio TV Out (Main)” setting is set to “On”
(
) or “Audio TV Out (Sub)” setting is set to
“On” (
) and you’re listening through your TV
speakers.
– “HDMI CEC (RIHD)” is set to “On” (
you’re listening through your TV speakers.
Explanatory Notes
a Setting target
b Setting options (default setting underlined)
b Setting options (default setting underlined)
You can change various audio settings from the
Quick Setup (
Quick Setup (
Note
• These settings are not available in either of the following
cases:
– The “Audio TV Out (Main)” setting is set to “On”
– The “Audio TV Out (Main)” setting is set to “On”
) or “Audio TV Out (Sub)” setting is set to
“On” (
) and you’re listening through your TV
speakers.
– “HDMI CEC (RIHD)” is set to “On” (
) and
you’re listening through your TV speakers.
Tone Control
■
Bass
`
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds
output from the front speakers.
output from the front speakers.
■
Treble
`
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds
output from the front speakers.
output from the front speakers.
You can adjust the bass and treble for the front
speakers, except when the Direct, Pure Audio
(European, Australian and Asian models) or THX
listening mode is selected.
speakers, except when the Direct, Pure Audio
(European, Australian and Asian models) or THX
listening mode is selected.
Operating on the AV receiver
Phase Matching Bass
■
Phase Matching Bass
`
Off
`
On
From the warm low notes produced by a cello to the
deep frequencies of electronic music, a good audio
system should be able to deliver plenty of bass
resonance.
While traditional enhancement systems effectively
boost low-frequency sound, they are often prone to
the effects of phase shifting, which can overwhelm
mid-range frequencies and muddy the sound. Our
Phase-Matching Bass Boost technology effectively
preserves mid-range clarity-allowing vocals and
strings to shine-while maintaining a smooth, powerful
bass response at all volume levels.
deep frequencies of electronic music, a good audio
system should be able to deliver plenty of bass
resonance.
While traditional enhancement systems effectively
boost low-frequency sound, they are often prone to
the effects of phase shifting, which can overwhelm
mid-range frequencies and muddy the sound. Our
Phase-Matching Bass Boost technology effectively
preserves mid-range clarity-allowing vocals and
strings to shine-while maintaining a smooth, powerful
bass response at all volume levels.
Note
• The Phase Matching Bass is disabled when the Direct,
Pure Audio (European, Australian and Asian models), or
THX listening mode is selected.
THX listening mode is selected.
• If the “Subwoofer” setting is set to “No”, this setting is fixed
to “Off”.
Operating on the AV receiver
■
Phase Matching Bass
`
Off
`
On
a
b
b
Using the Audio Settings of Quick
Setup
Setup
1
Press TONE repeatedly to select either “Bass”
or “Treble”.
or “Treble”.
2
Use – and + to adjust.
1
Press TONE repeatedly to select “PM Bass”.
2
Use – and + to change the setting.