Creek Audio EVO Merkblatt

POWER OUTPUT (both channels into 8

Ω)

85 Watts 

POWER OUTPUT (one channel into 8

Ω)

100 Watts 

POWER OUTPUT (one channel into 4

Ω)

170 Watts

PEAK OUTPUT CURRENT INTO 1

Ω

> 10 Amps RMS

TOTAL HARMONIC DISTORTION

< 0.1%

(20 Hz to 20 kHz)

FREQUENCY RESPONSE

5 Hz to 50 kHz - 1 dB

SLEW RATE

> 25 V per 

µ

S

GAIN 

x 68  

INPUT SENSITIVITY - One channel driven/8

Ω

415 mV line input

PRE-AMP OUTPUT LEVEL

Follows input signal level via volume control
X 2

SIGNAL TO NOISE RATIO (‘A’ weighted)

> 96 dB

SEPARATION (line inputs)

> 60 dB at 1 kHz

MM PHONO SENSITIVITY & IMPEDANCE

3.5 mV  47 k

Ω  (when fitted)

MC PHONO SENSITIVITY & IMPEDANCE

0.75 mV  1 k

Ω  (when fitted)

POWER CONSUMPTION (at idle)

40 W

POWER CONSUMPTION (full power 10% THD)

340 W

WEIGHT (net)

8.6 kgs     19 lbs

SIZE (W x H x D)

430 x 80 x 340 mm   17” x 3.2” x 15.5”

MAINS VOLTAGE

@ 60Hz

110/120V North America

@ 50Hz 

220/240V Europe, Asia and UK

REMOTE HANDSET

EVO Supplied  (Uses NEC codes)

Thank you for purchasing the Creek EVO. You are now in possession of a State of the Art integrated
amplifier. The functions and operation of the EVO are very simple. However, the following notes are
provided to explain all aspects of its design and use.

When unpacking the amplifier please keep the packing material in a safe place for possible future use.
In the pack there is a separate mains cable suitable for connecting to the mains supply in the country
of use.  The IEC socket end of the cable should be firmly inserted into the connector on the rear panel
marked "Mains Input". 

Before switching on the amplifier check the voltage selector switch on the rear panel to ensure it is set
correctly to the voltage of the country in which the amplifier is being used.

Remember, do not overload the mains wall socket with too many plugs or adaptors.  The high quality
performance of  the amplifier will be impaired if the electrical supply to it is in poor condition.  If in doubt,
consult a qualified electrician or your dealer. 

The ‘Mains Input’ connection is also fitted with a fuse. The value is clearly stated on the rear panel.

The rotary selector switch on the left-hand side of the amplifier is used to select and listen to any of the
desired inputs.  There are four inputs plus tape which is selected by the button marked tape. The
selected input will appear in the display.

As all the line input levels are the same, it is not absolutely necessary to use the precise inputs as
designated.  You may, for example, plug a CD player into the Tuner input and obtain exactly the same
result or performance as the dedicated CD input.  However, you need to be aware that the front panel
display will always reflect the input as designated on the rear panel. 

For added flexibility, the first input on the EVO can be used either for vinyl disc or auxiliary line. To
connect your turntable, it is necessary to have the optional MM or MC phono plug-in board fitted.
Alternatively Creek Audio produces a separate range of phono pre-amplifers.  Ask your dealer for full
details.  

A pre-amp output and power amp input are shared by RCA sockets on the rear panel marked preamp. 

If within two years of puchase date your Creek EVO proves to be defective for any reason other than
accident, misuse, neglect, unauthorized modifcation, or fair wear and tear, Creek Audio Ltd. will, at its
discretion, replace the faulty parts without charge for labour or return carriage within the U.K. This
warranty is valid only in the U.K. and given in addition to statutory rights. Service enquiries outside the
U.K. should be addressed first to the supplying dealer and/or the Creek distributor/importer. Warranties
granted in these countries are entirely at the discretion of the distributor.