Linn 328A Benutzerhandbuch

Explanation of symbols used in this manual and on the product:

This symbol is intended to aler t the user to the presence, within the
enclosure, of uninsulated dangerous voltages of sufficient magnitude to
cause electric shock. 

This symbol is intended to aler t the user to the presence of impor tant
maintenance and ser vicing information in the instruction and ser vice
manuals.

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.

GENERAL SAFETY INSTRUCTIONS

1.

Read instructions. Read the safety and operating instructions before operating 
the appliance.

2.  Retain instructions. Retain the safety and operating instructions for future 

reference.

3.  Heed warnings. Obser ve all warnings on the appliance and in the operating 

instructions.

4.  Follow instructions. Follow all operating and use instructions.
5.  Water and moisture. Do not use the appliance near water, for example near 

a bathtub, washbowl, kitchen sink, laundr y tub, in a wet basement, or near a 
swimming pool and the like.

6.  Car ts and stands. Use only with a car t or stand that is recommended by the 

manufacturer.

6a. An appliance and car t combination should be used with care. Quick stops, 

excessive force, and uneven sur faces may cause the appliance and car t 
combination to over turn.

7.  Wall or ceiling mounting. Mount to a wall or ceiling only as recommended by the

manufacturer.

8.  Ventilation. Site the appliance so that its location or position 

does not inter fere with its proper ventilation. For example, the appliance should 
not be situated on a bed, sofa, rug, or similar sur face that may block the 
ventilation openings, or placed in a built-in installation such as a bookcase or 
cabinet that may impede the flow of air through the ventilation openings.

9.  Heat. Site the appliance away from heat sources such as radiators, heaters, 

stoves, or other appliances (including amplifiers) that produce heat.

10. Power sources. Connect the appliance to a power supply only of the type 

described in the operating instructions or marked on the appliance.

11. Grounding or polarisation. Do not defeat the safety purpose of the polarised or 

grounding type plug. A polarised plug has two blades with one wider than the 
other. A grounding type plug has two blades and a third grounding prong. The 
wide blade or the third prong are provided for your safety. When the provided 
plug does not fit into your outlet, consult an electrician for replacement of the 
obsolete outlet.

12. Power cord protection. Route power cords so that they are not likely to be 

walked on or pinched by items placed upon or against them, paying par ticular 
attention to cords at plugs, power sockets, and at the point where they exit 
from the appliance.

13. Protective attachment plug. As a safety feature the product is equipped with an 

attachment plug containing overload protection. See the instruction manual 
about resetting or replacing the plug. Should the plug need replacing ensure 
that a replacement is used which has the same overload 
protection as the original.

14. Cleaning. The product should be cleaned only as recommended by the 

manufacturer.

15. Power lines. An outdoor antenna should be located away from power lines.
16. Outdoor antenna grounding. If an outdoor antenna is connected to the 

tuner/receiver ensure that the antenna system is grounded to provide some 
protection against voltage surges and static build up. In the USA see ar ticle 
810 of the National Electrical Code ANSI/NFPA 70 concerning installation 
requirements.

17. Lightning storms. Unplug this apparatus during lightning storms or when unused

for long periods of time.

18. Objects and liquid entr y. Do not let objects or liquids fall into the product.

Do not expose the product to dripping or splashing. Do not place a vessel 
containing liquid on top of the product.

19. Damage requiring ser vice. The product should be ser viced by qualified 

personnel if:

a) The power cord or plug has been damaged.
b) Objects or liquid have fallen into the product.
c)  The product has been exposed to rain.
d) The product does not appear to operate normally or 

exhibits a marked change in operation.

e) The product has been dropped or the enclosure damaged.

20. Ser vicing. Don’t attempt to ser vice the product beyond that described in the 

operating instructions. All other ser vicing should be referred to qualified ser vice
personnel.

Copyright and Acknowledgements

Copyright © 2003 Linn Products Limited. First edition June 2003.

Linn Products Limited, Floors Road, Water foot, Glasgow, G76 0EP, Scotland,
United Kingdom.

All rights reser ved. No par t of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or other wise, without the prior written consent
of the publisher. Linn and the Linn logo are registered trade marks of Linn Products
Limited.

Printed in the United Kingdom.

Linn Par t Number: PACK 848.

The information in this manual is furnished for informational use only, is subject to
change without notice, and should not be construed as a commitment by Linn
Products Limited. Linn Products Limited assumes no responsibility or liability for any
errors or inaccuracies that may appear in this manual.

Replacing the fuse in the mains plug

This appliance is fitted with a non-rewireable 10 Amp mains plug. The plug contains

a 10 Amp fuse. If the fuse has blown it can be replaced as follows:

a)  Pull out the red fuse cover/carrier.

b)  Remove and dispose of the blown fuse.

c)  Fit a new 10 Amp BS1362 approved fuse into the carrier and push the 

carrier  back into the plug. 

Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the

plug. Contact Linn to obtain a replacement fuse cover. Fuses are for fire protection

and do not protect against electric shock.

Mains plug replacement

Should your mains plug need replacing and you are competent to do this proceed as

follows. If you are in doubt contact your Linn retailer or a competent electrician.

a)  Disconnect the plug from the mains supply.

b)  Cut off the plug and dispose of it safely. A plug with bared conductors is 

dangerous if engaged in a live socket.

c)  Only fit a 10 Amp BS1363A approved plug with a 10 Amp fuse.

d)  The cable wire colours or a letter will be marked at the connection points of 

most quality plugs. Attach the wires securely to their respective points. The 

Brown wire must go to the Live pin, the Blue wire must go to the Neutral pin,

and the Green/Yellow wire must go to the Ear th pin.

e)  Before replacing the plug top ensure that the cable restraint is holding the 

outer sheath of the cable firmly and that the wires are correctly connected.

WARNING

THIS APPLIANCE MUST BE EARTHED.

CE Declaration of Conformity

Linn Products Ltd declare that this product is in conformance with the Low Voltage

Directive 73/23/EEC and Electromagnetic Compatibility 89/336/EEC as amended

by 92/31/EEC and 93/68/EEC.

The conformity of the designated product with the provisions of Directive number

73/23/EEC (LVD) is proved by full compliance with the following standards:

Standard number

Date of issue

Test type

EN60065 1998 

General 

requirements

Marking
Hazardous radiation
Heating under normal conditions
Shock hazards under normal 
operating conditions
Insulation requirements
Fault conditions
Mechanical strength
Par ts connected to the mains supply
Components
Terminal devices
External flexible cords
Electrical connections and mechanical fixings
Protection against electric shock
Stability and mechanical hazards
Resistance to fire

The conformity of the designated product with the provisions of Directive number

89/336/EEC (EMC) is proved by full compliance with the following standards:

Standard number

Date of issue

Test type

EN55013 2001 

Conducted 

emissions

EN55013

2001 Absorbed 

emissions

EN55020

2002

Immunity

FCC Notice

NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Par t 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful inter ference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful inter ference to radio communications. However, there is no
guarantee that inter ference will not occur in a par ticular installation.
If this equipment does cause harmful inter ference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to tr y to correct the inter ference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the  

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

English