MTX Audio TXC4.1 Benutzerhandbuch

BEFORE STARTING

MTX recommends that you have your new speakers installed by an authorized MTX retailer, prefer-
ably MECP certifi ed. If you do decide to do it yourself, make sure you have read the instructions
carefully and that you have the following tools:

• Electric drill

• Phillips bit or screwdriver

• 1/8” bit

• Door panel puller

• Wire cutters/crimpers

• Metal cutting tool

• Safety glasses

• 2mm hex wrench

• X-acto knife

Throughout installation, keep in mind the ultimate objective of creating an ideal soundstage and ex-
ceptional imaging. This refers to the experience you get when you sit in your seat with your head up
and shoulders straight, close your eyes, and listen. Where does the music seem to be coming from?
In an ideal world, you would hear all music from front and center, meaning it sounds like a band is
performing on your hood. Raising the soundstage is a very important process and every option should
be considered in order to have your sound as up and in front as possible.

Removing the Door Panel
Please be aware that today’s cars have door panels that are not designed to come apart easily; they
are designed by the factory to sit tight against the door and not rattle. It is important to note that if the
proper procedures are not followed, the door panels can easily become damaged and make them fi t
improperly when you’re trying to reinstall them.

Use a door panel puller to remove the door panel, and be aware there are often hidden screws that,
if overlooked, can cause the panel to crack or break when force is applied to remove door panel. It
might be a good idea to do some research on your specifi c car to be sure they are all removed before
continuing. Even new car owner needs to be aware of this potential issue. Buying a new door panel
is an expensive process so please take note of the potential for damage.

With the door panel off, it is a perfect time to add sound dampener. The main goal of sound dampen-
ers is to add mass to the metal in the door, causing less rattle and “ring” which will help to improve
the overall sound of your new speakers. It also helps prevent against outside noise by adding insula-
tion. Sound dampening material can be purchased from your local retailer and is available in many
different forms, and kits, for many different applications. Please make sure you purchase the correct
type for your specifi c project.

Note: Before cutting anything, please use common sense and make sure that no wires or glass will
interfere with cutting tools. ALWAYS WEAR PROPER SAFETY GLASSES. Be sure all wires are clear of
moving parts such as window crank mechanisms and trunk hinges. Use rubber grommets when run-
ning wires through sharp edged metal holes, which may wear through the wire’s insulation.

Do not mount speakers where they could come in contact with:

• The door’s window glass

• The window crank handle or gear assembly when rotated

• The trunk springs, shock towers, or trunk lid

• The gas tank or fuel lines

SPECIFICA

TIONS

Model

TXC4.1

TXC5.1

TXC6.1

TXC6.0

TXC.1

Description

4”
Components

5-1/4”
Components

6-1/2”
Components

6-1/2”
Woofer

25mm
Tweeter

Cone

Glass
Fiber with
Aluminum
Deposition

N/A

Tweeter

Teteron Dome

Teteron
Dome

Impedance

4 Ohm

Frequency
Response

50Hz-25kHz

45Hz-25kHz

43Hz-25kHz

43Hz-250Hz

3.5kHz-
25kHz

Power (RMS)

100

125

150

Peak Music Power

200

250

300

150

Sensitivity @ 2.83V

88dB

90dB

91dB

Voice Coil

1.25”

1.5”

25mm

X-Max

2.5mm

4.8mm

N/A

Woofer Mounting

1-3/4”

2-1/4”

N/A

Woofer Cut-out Dia.

3-1/2”

4-1/2”

5-19/32”

N/A

Tweeter Mounting
Depth

1”

N/A

1”

Tweeter Cut-out
Dia.

1-7/8”

N/A

1-7/8”

Tweeter Mounting
Options

Flush, Surface,
Angle

N/A

Flush, Surface,
Angle

Crossover Adjustable
Tweeter Level

0, -1.5, -3,
-4.5, -6

N/A

0, -1.5, -3,
-4.5, -6

Off-axis
Compensation

0, 30, 60
Degree

N/A

Bi-amp Inputs

Yes

N/A

INTRODUCTION

Thank you for choosing MTX to help reach your ultimate goal with your vehicle. Adding MTX TXC
High-end Component speakers and a matching MTX amplifi er with StreetWires connections will put
you in a better position to hear, feel, and experience all of the music the artist intended.

TXC series component speakers are the best in the MTX offering of full-range speakers. They offer
many added features that are designed for the distinguished listener. Five levels of tweeter attenua-
tion, three positions of Off-axis adjustments, and Bi-amp inputs are just some of the features that will
help reproduce the music with exceptional dynamics and detail regardless on mounting location and
position within the vehicle. The TXC series also offers an add-on midbass driver and/or tweeter that
further defi ne the musical experience. The TXC6.0 is an additional woofer that can change this 2-way
system into a true 3-way system, while the TXC.1 is an additional tweeter that adds a new dimension
to the imaging. Call 1-800-CALL-MTX for more information.

MTX002049 TXC Owners Manual.indd 2-3

4/6/05 3:30:42 PM