JBL 260 Benutzerhandbuch

 

Delay - On/Off
Length - Delay Time - Course, Fine
Units - Seconds,Feet,Meters

DELAY

DELAY

From program mode, press the Delay button.   Pressing the Data Wheel will select the effect parameter to be edited. 

Successive Presses of the Delay button will move you through pre and post crossover delays. 

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.

AFS   On/Off
AFS   Clear

Mode - Fixed/Live
Type- Speech, Low,Med and High

Number of filters 0-12
Number of filters fixed 0-12

Live filter Lift - On/Off
Lift After - 0-60

<PREV PG

NEXT PG>

The NEXT and PREV

 buttons scroll through

 the pages of selected module. 

<PREV PG

NEXT PG>

The NEXT and PREV

 buttons scroll through

 the pages of selected module. 

Input Level 1   -Inf to 20dB
Input Level 2   -Inf to 20dB
Master Level   -Inf to 20dB

Pink Noise On/Off
Pink Noise Level  -10 to 10dB

Output Channel 1-6   On/Off
Polarity +/-
Phase -180 to 0

FEEDBACK

I/O Section

From program mode, press the I/O button.  Pressing the Data Wheel will select the effect parameter to be edited.  

<PREV PG

NEXT PG>

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.

The NEXT and PREV

 buttons scroll through

 the pages of selected module. 

Subharmonic Synthesizer

OTHER

OTHER

From program mode, press the Other button.  Successive presses of the Other button will move you to each of the various insert modules available.

Pressing the Data Wheel will select the effect parameter to be edited.  

<PREV PG

NEXT PG>

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.

The NEXT and PREV

 buttons scroll through

 the pages of selected module. 

RTA/WIZARD

SYSTEM SETUP

AUTO EQ WIZARD

AFS WIZARD

GEQ Setup-Dual Mono
          or Stereo Linked

Main Speaker Select-
          See list

Sub Speaker Select-
          See list

Amp Select-
High, Mid, Low
See list

Amp Sensitivity-
 High, Mid, Low

Amp Level
High, Mid, Low          

Low Amp  
Bridged/
Normal-
          

Load New 
Program-
          

Insert 1 Setup-
 Select

Insert 2 Setup-
 Select

Noise gate-
 AGC-

Limiter

Limiter 4-6

Connect Mic

Pink Noise Level
-Inf to 20dB

Auto EQ - L

Auto EQ - R

Auto EQ - L-R

Left and Right when using

Linked Graphic EQ

Select Number of
Fixed Filters 
- 0-12

Mixer gain turn 
down prompt

Select Type - 
Low, Med, High mode

Mixer Gain Adjust- 

WIZARD

From program mode, press the RTA/WIZARD button. Pressing the Data Wheel will select the effect parameter to be edited.  

<PREV PG

NEXT PG>

Fixed Filter Setup
Done- 

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.

LCD Contrast  1-16
AEQ Plot - RTA/GEQ

UTILITY

PUP Prog.  -  Current/Stored
PUP Mute  -  Current/Stored

ZC Panel -        1-6
(Store) -         Edit Panel

Security Level - Module Select
Security Level-  Low, Med, High

260 Device Level-
Low, Med, High

Edit High Password
Edit Medium Password

Program List Size- 1-10
List Index -            1-10

Program Change mode
Normal/Program
Program Number Lock 1-25

Output Jumpers -       1-6
Setting -  14, 22, 30dB

UTILITY

METERS

From program mode, press the UTILITY button. Pressing the Data Wheel will select the effect parameter to be edited. 

Pressing and holding the Utility button will enter you into the meter mennu 

Subharmonic - -On/Off
Subharmonics % 0-100
 

24-36Hz Level - 24-36Hz
36-56Hz Level - 36-56Hz

Subharmonic

SUBHARMONIC

From program mode, press the SUBHARMONIC button.   Pressing the Data Wheel will select the effect parameter to be edited.  

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.

Advanced Feedback Suppression (AFS)

OTHER

Notch-   

On - Off

Flatten/Restore

Notch Filter

OTHER

Freq 1-6          19.7Hz-20.2kHz
Gain-     

-36dB - +6dB

Q-     

16,32,64,128

Subharmonic - -On/Off
Subharmonics % 0-100
 

24-36Hz Level - 24-36Hz
36-56Hz Level - 36-56Hz

 1-3

Zone Controller-
 1-3

Output Trims
1-3

Output Trims
4-6

 Zone Controller-
4-6

 

The Comp/Limiter button 

toggles through the AGC

Compressor or 

Limiter modules used in 

each channel of 

the selected 

program. 

COMP

Comp On/Off
Auto On/Off
Over Easy   Off, 1-10

DYNAMICS

Threshold   -40 to-20dB
Ratio 1:1 to Inf:1
Gain -20 to 20dB

Attack   0.1 to 200ms
Hold 30 to 200ms
Release 360 to 5.0dB/s

Max Atten   o to Inf

GATE

Gate On/Off
Ratio 1:1 to Inf:1
Threshold   -50-22dB

Attack   0.1 to 200ms
Hold 30 to 200ms
Release 360 to 5.0dB/s

Attack   .20 to 5 sec
Release 30 to 1.0dB/s

AGC(Pre)

AGC On/Off
Target  -20-20dBu
Gain   1 to 20dB

Window  1 to 10dB
Hold 30 to 200ms
Low Thresh -60to-30dB

Attack   .20 to 5 sec
Release 30 to 1.0dB/s

AGC(Post)

AGC On/Off
Target  -20-20dBu
Gain   1 to 20dB

Window  1 to 10dB
Hold 30 to 200ms
Low Thresh -60to-30dB

DYNAMICS

 From program mode, press the comp/limiter button  to move to eithter the Dynamics module. Once you have reached the Dynamics module, 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

successive presses of Dynamics button will move through each channel that utilizes either a Compressor (pre Crossover) or Limiter (post-crossover) module. 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Navigate through the Pages of the selected compressor or Limiter module by pressing the "Next Page" or "Prev Page" buttons successively until you arrive at the desired Page.

Attack   0.1 to 200ms
Hold 30 to 200ms
Release 360 to 5.0dB/s

LIMITER

Limiter On/Off
Over Easy   Off, 1-10
Threshold   -40-20dB

PeakStop On/Off
Auto On/Off
Overshoot   2 to 6dB

Successive presses of the Data wheel will select 

effect parameters within the currently selected page.