JVC RX-5000VBK Benutzerhandbuch
18
From the remote control:
1. Press SOUND CONTROL.
The 10 keys are activated for sound adjustments.
2. Press SURROUND repeatedly
until the DAP mode — DANCE
CLUB, LIVE CLUB, HALL, or
PAVILION — appears on the
display.
CLUB, LIVE CLUB, HALL, or
PAVILION — appears on the
display.
The DAP indicator also lights up on the display.
3. Press REAR•L – / + to adjust the
rear speaker output level.
• Pressing REAR•L – decreases the output
level up to –10 dB.
• Pressing REAR•L + increases the output
level up to +10 dB.
Note:
You cannot adjust the left and right rear speaker output levels
separately.
separately.
4. Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
As the number increases, the selected DAP mode becomes
stronger.
stronger.
Adjusting the Surround Modes — Dolby
Surround and JVC Theater Surround
Surround and JVC Theater Surround
Before you start, remember...
• Make sure that you have set the speaker information correctly
• Make sure that you have set the speaker information correctly
(see page 11).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You can only adjust the effect level when selecting JVC Theater
Surround.
• You can only adjust the rear and/or center speaker output levels
when you have connected rear speakers and/or a center speaker
and have set “REAR SPK” and/or “CNTR SPK” correctly. See
page 11.
and have set “REAR SPK” and/or “CNTR SPK” correctly. See
page 11.
From the remote control:
1. Press SOUND CONTROL.
The 10 keys are activated for sound adjustments.
2. Press SURROUND repeatedly
until the mode — “PROLOGIC”
or “3 STEREO” or “THEATER”
—appears on the display.
or “3 STEREO” or “THEATER”
—appears on the display.
• For “PROLOGIC” and “3 STEREO,” the PRO LOGIC
indicator lights up on the display.
• For “THEATER,” the PRO LOGIC and DAP indicators light
up on the display.
3. Press TEST to check the speaker
output balance.
“TEST ” starts flashing on the display, and a
test tone comes out of the speakers in the
following order:
test tone comes out of the speakers in the
following order:
Note:
You can adjust the speaker output levels without outputting the
test tone.
test tone.
4. Press CENTER – / + repeatedly to
adjust the center speaker output
level (from –10 to +10).
level (from –10 to +10).
5. Press REAR•L – / + to adjust the
rear speaker output level (from
–10 to +10).
–10 to +10).
Notes:
• You cannot adjust the left and right rear speaker output levels
separately.
• You cannot use the REAR•R – / + buttons to adjust the rear
speaker level.
6. Press TEST again to stop the test
tone.
7. ONLY FOR JVC Theater
Surround:
Press EFFECT to select an effect
level you want.
level you want.
• Each time you press the button, the effect
level changes as follows:
As the number increases, JVC Theater Surround becomes
stronger.
stronger.
EFFECT 1
EFFECT 2
EFFECT 4
EFFECT 3
EFFECT 5
SOUND
CONTROL
SOUND
CONTROL
Left front speaker
Rear speaker
Center speaker
Right front speaker
3
SURROUND
4
EFFECT
5
3
SURROUND
2
5
TEST
2
5
TEST
4
EFFECT
5
EFFECT 1
EFFECT 2
EFFECT 4
EFFECT 3
EFFECT 5
9
8
– REAR•L +
5
6
5
– CENTER +
5
9
8
– REAR•L +
5
EN08-20.RX-5000V[J]/F
99.10.29, 9:09 AM
18