Panasonic RQT9708-1P Benutzerhandbuch

RQT9708

With this feature you can wirelessly stream music 

to this unit’s speakers.

∫ Compatible devices

(as of December 2011)

AirPlay works with;
≥ iOS 4.2 or later (iPod touch (2nd, 3rd, and 4th 

generation), iPhone 4S, iPhone 4, iPhone 3GS, 
iPad 2, iPad)

≥ iTunes 10.2 or later (Mac / PC)

To use the AirPlay function, this unit must join the 
same wireless network as the compatible device.

Preparation
With this unit there are 2 methods to setup the 
wireless connection. Determine which type of 
wireless network router you are using and follow 
the method that matches your device.
≥ Refer to the operating instructions of the wireless 

network router for details.

≥ Turn the unit on.

≥ When performing the network settings, place this unit close 

to the wireless router.

≥ Simultaneous use with other 2.4 GHz devices, such as 

microwaves, cordless telephones, etc., may result in 
connection interruptions.

≥ Immediately after this unit is turned on, the network setup 

may take longer to start.

≥ This unit cannot join a wireless network using WEP security 

settings with “Method 1”. Use “Method 2” to join the wireless 
network.

≥ To cancel this setting in the middle, press [Í] to turn off the 

unit.

≥ For up to date compatibility information on your Wireless 

router refer to 
http://panasonic.jp/support/global/cs/
(This site is in English only.)

∫ Using the WPS Push Button Configuration 

(PBC)

Press and hold [– WPS] on the unit.

{. “CONNECT” flashes on the display. (Wi-Fi status 

indicator blinks blue.)

≥ Complete step 2 within 2 mins.

Press the WPS button on the wireless router.

{. When a link is established “LINKING” is indicated on 

this unit’s display.

{. When the configuration is finished “SUCCESS” is 

indicated on this unit’s display. (Wi-Fi status indicator 
lights blue.)

Press [OK] on the remote control to complete 

the setting.

≥ This unit can also be set using the WPS PIN code.

Replace step 2 of “Method 1” with the following steps.
(Before starting, refer to the wireless network router’s 
operating instructions for details on how to enter the PIN 
code.)
1

While “CONNECT” is flashing press and hold [– WPS] 
again to display the 8 digit PIN code. (Wi-Fi status 
indicator blinks purple.)

2

Enter the PIN code into the wireless router.

≥ To edit this system’s name it is necessary to use “Method 2”.
≥ “FAIL” may be displayed if the connection was not made 

within the set time limit. Try the setting again. If “FAIL” is still 
displayed, try “Method 2”.

With this method, you will access this unit’s 
wireless network settings from the Internet browser 
of your compatible device.

≥ The illustrations and explanations are based on an iPhone. 

However, the word “iPhone” can be replaced with your 
compatible device.

Preparation
≥ Check your home wireless network name 

(Network name (SSID)) and password for this 
network. This can often be found on the wireless 
router itself.

≥ Turn on your iPhone.

(Continues to next page)

*1: WPS stands for “Wi-Fi Protected Setup

TM

”.

If you do not know which type of wireless network 
router you are using, use “Method 2”.

Method 1

If your wireless network router supports WPS*

1

.

WPS Push Button Configuration 
(PBC) compatible wireless router 
may have this mark.

Method 2

If your wireless network router does not support 
WPS*

1

.

SC-HC57~RQT9708.book  9 ページ  ２０１２年３月２日　金曜日　午後２時４分