JVC KD-G614 Benutzerhandbuch

2

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the receiver.
•  Be sure to ground this receiver to the car’s chassis again after installation.

Notes:
•  Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
•  It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 

Ω to 8 Ω). 

If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 21 of the INSTRUCTIONS).

•  To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
•  The heat sink becomes very hot after use. Be careful not to touch it when removing this receiver. 

Heat sink

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in color.

  Connect the colored leads of the power cord in the order specified in the illustration below.

  Connect the antenna cord.

  Finally connect the wiring harness to the receiver.

*

2 

Before checking the operation of this 
receiver prior to installation, this lead must 
be connected, otherwise power cannot be 
turned on.

Line out (see diagram   )

Rear ground 
terminal

15 A fuse

Black

Blue with white stripe

Red

Yellow

*

2

*

1

 

Not included for this receiver

To metallic body or chassis of the car

Ignition switch

Fuse block

To an accessory terminal in the fuse block

To the remote lead of other equipment (200 mA max.)

Left speaker (front)

Right speaker (front)

Left speaker (rear)

Right speaker (rear)

Purple

Purple with black stripe

Green

Green with black stripe

Gray

Gray with black stripe

White

White with black stripe

To a live terminal in the fuse block connecting to the car battery 
(bypassing the ignition switch) (constant 12 V)

SUBWOOFER

*

3

Blue

To CD changer or another external component (see diagram   )

Antenna terminal

*

3

 

Only for KD-G614 (see diagram   )

To the automatic antenna if any 
(250 mA max.)

Orange with white stripe

Brown

To car light control switch

To cellular phone system—only for KD-G614

You can connect amplifiers to upgrade your car stereo system.
•  Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this receiver.
•  Disconnect the speakers from this receiver, connect them to the amplifier. Leave the speaker leads of this receiver unused.

*

4

  Firmly attach the ground wire to the 

metallic body or to the chassis of the 
car—to the place not coated with paint 
(if coated with paint, remove the paint 
before attaching the wire). Failure to do 
so may cause damage to the receiver.

Front speakers

Rear speakers

Remote lead

Y-connector (not supplied for this receiver)

Remote lead (Blue with white stripe)

To the remote lead of other equipment or auto antenna if any

Front speakers

Subwoofer

Only for KD-G614

Only for KD-G614

*

5

  Signal cord (not supplied for this receiver)

•  Before connecting the CD 

changer, make sure that the 
receiver is turned off.

*

6

  Connecting cord supplied for 

your CD changer

•  Refer also to page 13 of the INSTRUCTIONS.

*

7

  Only for KD-G614

*

8

  Line Input Adapter KS-U57 

(not supplied for this receiver)

KS-U57*

8

Instal1-2_G614_G514_002A_f.indd   3

Instal1-2_G614_G514_002A_f.indd   3

12/22/04   11:27:49 PM

12/22/04   11:27:49 PM