Lanzar Car Audio SDBT75NU Benutzerhandbuch
24
OPERATION
RADIO OPERATION
Switching to radio mode
Press MODE button on remote control
to select radio mode or tap the Radio
icon on the SOURCE menu on the
screen.
In radio mode, the following information
will appear on the display.
to select radio mode or tap the Radio
icon on the SOURCE menu on the
screen.
In radio mode, the following information
will appear on the display.
Selecting the frequency band
Press BAND on remote control or tap
BAND bar on the screen to select
desired band. The reception band will
change in the following order:
For two wave bands:
BAND bar on the screen to select
desired band. The reception band will
change in the following order:
For two wave bands:
Selecting station
During radio mode, shortly press
button on the front panel or on the
remote control or tap
button on the front panel or on the
remote control or tap
icon on
the screen to increase frequency, shortly
press button on the front panel or on
press button on the front panel or on
the remote control or tap
icon
on the screen to decrease frequency
by one step of channel spacing. Hold
the button longer for fast tuning. The
frequency is updated correspondingly
on display.
Press and hold
by one step of channel spacing. Hold
the button longer for fast tuning. The
frequency is updated correspondingly
on display.
Press and hold
/
buttons on the
front panel, “Manual” will appear on the
screen display, you can adjust the
frequency manually. If there is no
operation for about 5 seconds, “Manual”
will disappear. The system will exit this
mode.
screen display, you can adjust the
frequency manually. If there is no
operation for about 5 seconds, “Manual”
will disappear. The system will exit this
mode.
Setting memory
Press RADIO PRESET buttons (1~6)
on remote control or press
on remote control or press
/
on the
front panel or on the remote control to
preset stations at radio mode. With this
system, a total of 24 stations (for two
wave band) or 30 stations (for three
wave band) can be stored in the
memory of six buttons.
Each band stores up to six preset
stations.
preset stations at radio mode. With this
system, a total of 24 stations (for two
wave band) or 30 stations (for three
wave band) can be stored in the
memory of six buttons.
Each band stores up to six preset
stations.
The stations might be FM1, FM2, FM3,
MW band. The operation is as below:
MW band. The operation is as below:
- Store in Memory Press and hold
desired memory location button for
several seconds. The current listening
station will be stored into the number
button.
several seconds. The current listening
station will be stored into the number
button.
- Or tap “CH” character on the screen
then press and hold M1~6 button
bars on the screen will stored the
current station to the location button.
bars on the screen will stored the
current station to the location button.
- Retrieve a Preset Station
Press any one of the RADIO PRESET
buttons (1~6) on remote control to
retrieve a station which had been
stored in the memory in advance the
hosen number is shown on display.
buttons (1~6) on remote control to
retrieve a station which had been
stored in the memory in advance the
hosen number is shown on display.
Automatic Memory Story & Program
Scanning
- Program scanning
- Program scanning
Shortly press AS/PS button on remote
control or on the front panel to scan
preset station. And it will hold at each
station for about 5 seconds.
control or on the front panel to scan
preset station. And it will hold at each
station for about 5 seconds.
- Automatic memory storing
Press and hold AS/PS button on
remote control for about several
seconds or press AS/PS button on
the front panel, the radio searches
from the current frequency and checks
the signal strength until one cycle
search is finished. And then stations
are stored into the preset number
button in turn according to the
strength of the stations.
When auto search is finished, it will
enter into preset scan mode
automatically.
Note: In FM mode press and hold 1-
6 numeric buttons on the front panel
or on the remote control fro about 2
seconds, will store the current station
to the current numeric key position.
remote control for about several
seconds or press AS/PS button on
the front panel, the radio searches
from the current frequency and checks
the signal strength until one cycle
search is finished. And then stations
are stored into the preset number
button in turn according to the
strength of the stations.
When auto search is finished, it will
enter into preset scan mode
automatically.
Note: In FM mode press and hold 1-
6 numeric buttons on the front panel
or on the remote control fro about 2
seconds, will store the current station
to the current numeric key position.
Mono/Stereo
Press MO/ST button on remote control
to select mono or stereo mode. You
can sometimes improve reception of
distant stations by selecting mono
operation.
to select mono or stereo mode. You
can sometimes improve reception of
distant stations by selecting mono
operation.
Local/Distant
Press and LOC button on the remote
control to select between local and
distant stations.
Local setting for reception of strong
Station, and a distant setting
forreception of weaker stations.
control to select between local and
distant stations.
Local setting for reception of strong
Station, and a distant setting
forreception of weaker stations.
FM1 FM2 FM3 AM