Alpine CDA-7862 Benutzerhandbuch
9
-EN
Default values
BC: 80 Hz
BW: WIDE1
TC: 10.0kHz
HP: OFF
LP: OFF
SUBW (Phase): NOR
BC: 80 Hz
BW: WIDE1
TC: 10.0kHz
HP: OFF
LP: OFF
SUBW (Phase): NOR
NOTES
• If you turn the battery power OFF, all settings return to factory
default.
• If HP, LP, BC, and TC are all set to ON, depending on the BC and
TC settings, you may not be able to reinforce the sound effect.
• Except when the HP and LP is turned OFF, the subwoofer is in
monaural mode.
• When the subwoofer is set to OFF, LP mode and change of
phase does not work.
• If no buttons are pressed within 5 seconds, the display for setup
menu disappears while an ordinary menu appears on the
display.
display.
Blackout Mode On and Off
(CDA-7965 only)
(CDA-7965 only)
When the Blackout mode is turned on, the CFL
display will turn off to reduce power consumption.
This additional power enhances the sound quality.
display will turn off to reduce power consumption.
This additional power enhances the sound quality.
1
Press and hold the BLACK OUT button for at
least 2 seconds to start the blackout mode. The
display panel lighting turns off, and the audio
signals bypass the treble and bass circuits. This
reduces noise to give a clean, flat response.
least 2 seconds to start the blackout mode. The
display panel lighting turns off, and the audio
signals bypass the treble and bass circuits. This
reduces noise to give a clean, flat response.
NOTE
If any button on the unit is pressed during the blackout
mode, the function will be displayed for 5 seconds to show
the operation before returning to Blackout mode.
If any button on the unit is pressed during the blackout
mode, the function will be displayed for 5 seconds to show
the operation before returning to Blackout mode.
To cancel the blackout mode, press and hold the
BLACK OUT button for at least 2 seconds.
BLACK OUT button for at least 2 seconds.
Switching the Display Modes
1
Press the DISP (DISPLAY) button to select the
desired Display pattern mode.
desired Display pattern mode.
Each press changes the display patterns.
Pattern
1
2
3
4
5
6
7
8
9
10
Description
Frequency Pattern
Normal Pattern (Upward)
Peak Value Increasing Pattern
Elevator (left/right) Pattern
Elevator (up/right) Pattern
Warp Pattern
Center Division Pattern
Scan Display
(Repeats from Pattern 1 to Pattern 7
for every 5 seconds endlessly.)
(Repeats from Pattern 1 to Pattern 7
for every 5 seconds endlessly.)
Mode Display
Silent Display (Spectrum analyzer Off)
2
Within 5 seconds, press the DN g or
f UP button repeatedly to select the desired
parameter.
f UP button repeatedly to select the desired
parameter.
→ ∗BC or BW → TC → HP
DEFP
DEFP
← SUBW ← LP ←
∗ Each time you press the MODE (Audio Control)
knob, the BC and BW change alternatery.
3
Press the MODE (Audio Control) knob to toggle
between the BC and BW.
between the BC and BW.
1. BC (Setting the Bass Frequency):
→ 60Hz → 70Hz → 80Hz → 90Hz
180Hz
180Hz
← 150Hz ← 130Hz ← 100Hz ←
Emphasizes the displayed Bass frequency
ranges.
ranges.
2. BW (Setting the Bass Band Width):
(Q-Factor)
→ WIDE1 → WIDE2 → WIDE3 → WIDE4
(Narrow)
←.................................→ (Wide)
Changes the displayed frequency’s band width
to narrow or wide.
to narrow or wide.
NOTE
A narrow or wide wave pattern on the display will
indicate the selected band width.
A narrow or wide wave pattern on the display will
indicate the selected band width.
3. TC (Setting the Treble Frequency):
→ 10.0kHz → 12.5kHz → 15.0kHz → 17.5kHz
Emphasizes the displayed treble frequency
ranges.
ranges.
4. HP (Setting the High Pass Filter):
→ OFF → 80Hz
→ 120Hz
→ 160Hz
Outputs all frequencies higher than that selected
according to your preference.
according to your preference.
5. LP (Setting the Low Pass Filter):
→ OFF → 160Hz
→ 120Hz
→ 80Hz
Outputs all frequencies lower than that selected
according to your preference.
(Only available when using the subwoofer output
from this unit.)
according to your preference.
(Only available when using the subwoofer output
from this unit.)
6. SUBW (Change the Subwoofer Phase):
NOR
↔ REV
You can change the subwoofer phase.
(Only available when using the subwoofer output
from this unit.)
(Only available when using the subwoofer output
from this unit.)
7. DEFP (Defeat On and Off):
ON
↔ OFF
When DEFEAT is turned ON, all items 1 to 6 are
set to default values.
When DEFEAT is turned OFF, all items 1 to 6
resume their last set values.
set to default values.
When DEFEAT is turned OFF, all items 1 to 6
resume their last set values.