Fusion CP-AW1120 Merkblatt
ACTIVE WEDGE
SPECIFICATIONS
CP-AW1120
CP-AW2120
Peak Power (Watts)
750
900
Rated Power (Watts)
250
300
Frequency Response
32Hz - 250Hz
32Hz - 250Hz
Low Pass Filter (Variable)
40Hz - 250Hz
40Hz - 250Hz
Tuning
Bass Reflex
Bass Reflex
Woofer Size
12”
Dual 12”
Fuse
25A
30A
Dimensions (mm)
567(l) x 415(w) x 384(h)
836(l) x 415(w) x 384(h)
22-5/16 x 16-11/32 x 15-3/32” 32-29/32 x 16-11/32 x 15-3/32”
CP-AW1120, CP-AW2120
www.fusionelectronics.com
CONTROL DESCRIPTIONS
LEVEL
This allows the adjustment of the amplifier level of the subwoofer.
Turn clockwise to increase the level. If the sound becomes distorted
reduce the level.
LEVEL
This allows the adjustment of the amplifier level of the subwoofer.
Turn clockwise to increase the level. If the sound becomes distorted
reduce the level.
LOW PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Active
Wedge will produce. This should be adjusted to blend with your main
speakers. Typically, this will be set to around 100Hz (approximately
the central position of the control knob).
This allows the adjustment of the highest frequency the Active
Wedge will produce. This should be adjusted to blend with your main
speakers. Typically, this will be set to around 100Hz (approximately
the central position of the control knob).
REMOTE LEVEL CONTROLLER
When connected, this allows further control over the level from a
remote location, using the supplied lead.
When connected, this allows further control over the level from a
remote location, using the supplied lead.
INSTALLATION
Make sure the Active Wedge is firmly fixed in your vehicle. Check
before drilling or cutting holes. DO NOT work near gas tanks, fuel
lines, hydraulic lines or electrical wiring.
DO NOT mount the Active Wedge in such a way as to pinch or
damage the wires.
Make sure everything is firmly connected, before attaching the
+12V wire. Ensure the +12V wire is fused as close as possible to the
battery. Always use a fuse with the recommended rating.
Make sure the Active Wedge is firmly fixed in your vehicle. Check
before drilling or cutting holes. DO NOT work near gas tanks, fuel
lines, hydraulic lines or electrical wiring.
DO NOT mount the Active Wedge in such a way as to pinch or
damage the wires.
Make sure everything is firmly connected, before attaching the
+12V wire. Ensure the +12V wire is fused as close as possible to the
battery. Always use a fuse with the recommended rating.
DISCLAIMER
Always ensure the Active Wedge is securely attached, to avoid movement. FUSION accepts no responsibility for damage or injury in relation
to inappropriate securing of this product.
Always ensure the Active Wedge is securely attached, to avoid movement. FUSION accepts no responsibility for damage or injury in relation
to inappropriate securing of this product.
WIRING
• Connect the ground wire to the vehicle first (clean dirt and paint
to bare metal).
• Connect the remote on (blue wire).
• Connect the RCA cables if applicable, OR
• Connect the speaker level wire by splicing into the headunits
speaker wires. See Note 1 on reverse.
• Connect the remote level controller with the supplied lead.
• Connect the 12 volt (red wire) to the positive battery terminal.
• Check all connections.
• Connect the ground wire to the vehicle first (clean dirt and paint
to bare metal).
• Connect the remote on (blue wire).
• Connect the RCA cables if applicable, OR
• Connect the speaker level wire by splicing into the headunits
speaker wires. See Note 1 on reverse.
• Connect the remote level controller with the supplied lead.
• Connect the 12 volt (red wire) to the positive battery terminal.
• Check all connections.