Fusion EN-AT1120 Merkblatt
ENCOUNTER
ACTIVE ENCLOSURES
EN-AT1100, EN-AT1120
Disclaimer
The provided self adhesive feet are intended for initial site placement only, and are not to be considered a suitable method
of securing the Active Enclosure. Always ensure the Active Enclosure is securely attached, to avoid movement.
of securing the Active Enclosure. Always ensure the Active Enclosure is securely attached, to avoid movement.
FUSION accepts no responsibility for damage or injury in relation to inappropriate securing of this product
Product Specifications
Control Descriptions
LEVEL
This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If the sound becomes
distorted reduce the level.
LOW PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce. This should be adjusted to
blend with your main speakers. Typically, this will be set to around 100Hz (approximately the central position of the control knob).
BASS
This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound becomes distorted, reduce
the amount of boost.
REMOTE LEVEL CONTROLLER
When connected, this allows further control over the level from a remote location, using the supplied lead.
LEVEL
This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If the sound becomes
distorted reduce the level.
LOW PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce. This should be adjusted to
blend with your main speakers. Typically, this will be set to around 100Hz (approximately the central position of the control knob).
BASS
This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound becomes distorted, reduce
the amount of boost.
REMOTE LEVEL CONTROLLER
When connected, this allows further control over the level from a remote location, using the supplied lead.
Installation
Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near
gas tanks, fuel lines, hydraulic lines or electrical wiring.
Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near
gas tanks, fuel lines, hydraulic lines or electrical wiring.
DO NOT mount the Encounter Active Enclosure in such a way as to pinch or damage the wires.
Make sure everything is firmly connected, before attaching the +12V wire. Make sure the +12V wire is fused as close as possible
to the battery. ALWAYS use a fuse with the recommended rating.
Two types of self-adhesive feet are included in the packaging. The rubber feet are to protect the bottom of the enclosure, or the
surface it is mounted to. There are four feet, which correspond to four indentations (feet and indentations are the same shape) in
the bottom of the enclosure end plates. Peel off the paper covering the rubber feet, and adhere to the indentations.
to the battery. ALWAYS use a fuse with the recommended rating.
Two types of self-adhesive feet are included in the packaging. The rubber feet are to protect the bottom of the enclosure, or the
surface it is mounted to. There are four feet, which correspond to four indentations (feet and indentations are the same shape) in
the bottom of the enclosure end plates. Peel off the paper covering the rubber feet, and adhere to the indentations.
There are also four Velcro feet (both hook and eye parts, both with self-adhesive properties) included. These are for assisting
in fixing the location of the enclosure. Peel off the paper covering and adhere one part to the indentations in the enclosure end
plates, and the matching part to the mounting surface. Always clean the surfaces before applying the adhesive part
in fixing the location of the enclosure. Peel off the paper covering and adhere one part to the indentations in the enclosure end
plates, and the matching part to the mounting surface. Always clean the surfaces before applying the adhesive part
EN-AT1100
EN-AT1120
Max Power Rating
300 Watts
360 Watts
Frequency Repsonse
35Hz - 250Hz
30Hz - 250Hz
Bass Boost (Variable)
0 / + 18dB
0 / + 18dB
Low Pass Filter (Variable)
40Hz - 250Hz
40Hz - 250Hz
Tuning
Bass Reflex
Bass Reflex
Woofer Size
10”
12”
Fuse
15 Amp
15 Amp
Tube Dimensions
550mm x 306mm x 306mm
21 11/16” x 12 1/16” x 12 1/16”
21 11/16” x 12 1/16” x 12 1/16”
590mm x 365mm x 365mm
23 1/4” x 14 3/8” x 14 3/8”
23 1/4” x 14 3/8” x 14 3/8”