Hitachi CCD Camera Benutzerhandbuch

 

 

1)  Press the SET button for at least 2 seconds to display 

the main menu on the monitor screen.

 

 
 
 
 
 
 
 
 
 
 

2) 

Check the present settings at the main menu.

 

3)  Shift the cursor vertically by pressing the UP and DOWN   

buttons, then press the SET button to enable changing the   
setting of the selected item. 

4)  If changes are unnecessary, shift the cursor to “END” and   

Press the SET button to return to the normal screen. 

5)  When an item indicated by a

 

↵ 

mark is selected, pressing 

the SET button shifts to the next menu. 

 

Three rear panel setup buttons are used to shift the cursor and 
select items from the menus. 
 
 
 
 
 
 
 
 
 
①

  Up button 

: Shift the cursor in the upward direction or 

increase an adjustment value. 

②

  Down button 

: Shift the cursor in the downward direction 

or decrease an adjustment value. 

③

  Set button 

: Press to display the main menu or to   

change a setting. 

 

       ◆◆

  ＭＡＩＮ  ＭＥＮＵ 

◆◆

 

 

>

ＣＡＭＥＲＡ  ＴＩＴＬＥ  ：ＯＦＦ 

↵

 

  ＬＩＧＨＴ  ＣＯＮＴＲＯＬ：ＯＦＦ 

↵

 

  ＡＧＣ                    ：ＯＮ 

↵

 

  ＳＨＵＴＴＥＲ  ＳＰＥＥＤ：ＯＦＦ 
  ＳＥＮＳ  ＵＰ            ：ＯＦＦ 
  Ｂ／Ｗ  ＭＯＤＥ          ：ＯＦＦ 
  ＷＨＩＴＥ  ＢＡＬＡＮＣＥ：ＡＴＷ 

↵

 

  ＳＵＢ  ＭＥＮＵ 

↵

 

  ＥＮＤ 

 
 
……

  Camera title setting menu

 

……

  Light control setting menu 

……

  AGC setting menu 

……

  Shutter speed setting 

……

  Sensitivity enhance Setting 

……

 B/W mode setting (*) 

……

  White balance mode setting menu (*) 

……

 Sub menu 

……

  End of menu display 

 

Note: 
lf no button is pressed, the menu display extinguishes 
automatically after about 5 minutes.

 

①

 

②

 

③

 

One line of up to 22 alphanumeric characters can be displayed   
on the screen. The display on/off and position are selected at the
camera title menu. 
1)  Press the SET button for longer than 2 seconds to display   

the main menu. 

2)  Use the UP and DOWN buttons to shift the cursor to   

“CAMERA TITLE”, then press the SET button to display the 
camera title menu. 

3)  While the cursor is at “MODE”, press the SET button to shift 

the mode in the sequence “OFF”, “TOP”, “BOTTOM”. 

Characters not displayed. (Factory setting)

Characters displayed at top of screen. 

Characters displayed at bottom of screen.

 

 

1)  When the mode is Top or Bottom, the characters indicated in 

the figure can be used. 

 
 
 
 
 
 
 
 
 
 
2)  Press the DOWN button, then use the UP and DOWN   

buttons to shift the flashing cursor sequentially among the 
usable characters. 

3)  When the SET button is pressed, the selected character is   

entered in sequence beginning with the left-most of 22 dots 
shown at the bottom of the screen.   
Afterwards, each newly selected character is entered   
sequentially toward the right. 

The item under character input selecting department uses it in 
the following manner. 

To add a blank space, shift the flashing cursor to   

“SPACE”, then press the SET button. 

 

  ◆

  ＣＡＭＥＲＡ  ＴＩＴＬＥ  ＭＥＮＵ 

◆

 

 

>

ＭＯＤＥ        ：ＯＦＦ 

 

   
 
 
 
 
 
 
  ＲＥＴ 
  ＥＮＤ 

 
 
……

  Display On/OFF and position

 

   

  ( OFF / TOP / BOTTOM ) 

 
 
 
 
 
 
……

  Return to the main menu 

……

  End of menu display 

 

  ◆

  ＣＡＭＥＲＡ  ＴＩＴＬＥ  ＭＥＮＵ 

◆

 

 

>

ＭＯＤＥ              ：ＴＯＰ 

 

        ０１２３４５６７８９ 
        ＡＢＣＤＥＦＧＨＩＪＫＬＭ 
        ＮＯＰＱＲＳＴＵＶＷＸＹＺ 
        ！？＃＆（ ）、 ．

：；～＊％ 

        ＋－ｘ／＝“‘ 
 
  ＳＰＡＣＥ      ←      →    ＲＥＳＥＴ 
  ＰＯＳＩＴＩＯＮ  ＲＥＴ      ＥＮＤ 

ＣＡＭＥＲＡ  ＮＯ．１・・・・・・・・・・・ 

 
 
……

  Display On/OFF and position

 

   

  ( OFF / TOP / BOTTOM ) 

 
   

Input character select table 

 
 
 
……

  Blank, cursor shift (left / right), character delete 

……

  Display position, return, end 

……

 Input character display 

 

13

14