Canon VB101 Benutzerhandbuch
Setup Procedures
3
49
Detail Settings
Picture Recording and output :
triggered by external device
Use this setting to operate the Picture
Recording function when recording is
performed in conjunction with an external
device such as a sensor or switch.
For a detailed example of actual operation,
see Chapter 6, "Using the Picture Recording
Function". (
triggered by external device
Use this setting to operate the Picture
Recording function when recording is
performed in conjunction with an external
device such as a sensor or switch.
For a detailed example of actual operation,
see Chapter 6, "Using the Picture Recording
Function". (
→ P.118)
"External Device Input 1/2"
"Recording at ON event"
Tick this option to record pictures when an
"ON" event is detected from an external
device.
Tick this option to record pictures when an
"ON" event is detected from an external
device.
"Recording between ON event and OFF event"
Tick this option to record pictures for as
long as an "ON" status continues from the
external device.
Tick this option to record pictures for as
long as an "ON" status continues from the
external device.
"Recording at OFF event"
Tick this option to record pictures when an
"OFF" event is detected from an external
device.
Tick this option to record pictures when an
"OFF" event is detected from an external
device.
"Camera Position"
Selects the camera angle used when
pictures are recorded. Select "Not
specified", "Home 1" to "Home 4" or
"Preset 1" to "Preset 8".
Selects the camera angle used when
pictures are recorded. Select "Not
specified", "Home 1" to "Home 4" or
"Preset 1" to "Preset 8".
"Pre-event Recording (sec.)"
When you want to save the pictures that
proceeds an ON or OFF event, use this
setting to enter the required number of
seconds.
When you want to save the pictures that
proceeds an ON or OFF event, use this
setting to enter the required number of
seconds.
"Post-event Recording (sec.)"
When you want to save the pictures that
follows an ON or OFF event, use this
setting to enter the required number of
seconds.
When you want to save the pictures that
follows an ON or OFF event, use this
setting to enter the required number of
seconds.
"Recording Interval between events"
Records pictures at set intervals between
ON and OFF event. Specify a value
between 10 and 600 seconds as the
sampling interval.
Records pictures at set intervals between
ON and OFF event. Specify a value
between 10 and 600 seconds as the
sampling interval.
"Output to External Device 1/2"
Tick this check box when you want to
control output to an external device. Keep
in mind that output to an external device
may not always be possible from Admin
Viewer or WebView Livescope MV ver.
2.0.
Tick this check box when you want to
control output to an external device. Keep
in mind that output to an external device
may not always be possible from Admin
Viewer or WebView Livescope MV ver.
2.0.
"Delay from OFF event (sec.)
When controlling output to an external
device and output must retain ON after
input is set to OFF, use this setting to
specify a delay of up to 20 seconds.
When controlling output to an external
device and output must retain ON after
input is set to OFF, use this setting to
specify a delay of up to 20 seconds.
"Set operation time"
When you tick this option, input from an
external device is limited to the operation
time specified below. Enter the start time
and end time for the intervals during
which external input is acceptable.
When you tick this option, input from an
external device is limited to the operation
time specified below. Enter the start time
and end time for the intervals during
which external input is acceptable.
"Handle ON/OFF input in reverse"
On some devices, ON and OFF are
reversed. Use this setting for such devices.
On some devices, ON and OFF are
reversed. Use this setting for such devices.
External device common settings
When using WebView Livescope MV ver. 2.0, if external
device settings are made, all names will be reflected in
MV.
When using WebView Livescope MV ver. 2.0, if external
device settings are made, all names will be reflected in
MV.