Philips CED750 Merkblatt
English
Connect wires: ISO connectors
1
Pull out the ISO connectors from the car
dashboard and connect them to the bigger
end of the supplied standard connector.
end of the supplied standard connector.
2
Connect the other end of supplied standard
connector to the unit.
If necessary, connect the following:
•
Connector Connect to/with
1
Black cable
Antenna
2
Yellow cable Video out 1
3
Yellow cable Video out 2
4
Yellow cable Camera in
5
Green/white
wire
wire
Parking
6
Black cable
Bluetooth microphone
7
Blue cable
Subwoofer
8
Red cable
Front line out L
9
White cable Front line out R
0
Red cable
Rear line out L
!
white cable Rear line out R
Mount in the dashboard
Note
Check wire connection before you mount
•
the unit into a car.
If preset radio stations are lost when the
If preset radio stations are lost when the
•
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
ON, reconnect the red leads crosswise to
the yellow ones.
1
If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car battery.
terminal of the car battery.
If you disconnect the car battery in
•
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
If the car battery is not disconnected,
lost its memory.
If the car battery is not disconnected,
•
to avoid short-circuit, ensure that bare
wires do not touch each other.
wires do not touch each other.
2
Ensure that car dashboard opening is within
these measurements:
Since the unit cannot be used if the
•
dashboard opening’s slant angle is above
20 degrees: Ensure that the horizontal
slant of the car dashboard opening is
between 0 and 20 degrees
20 degrees: Ensure that the horizontal
slant of the car dashboard opening is
between 0 and 20 degrees
3
Remove the screws on the both side of the
unit.
4
Remove the mounting sleeve.
5
Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
6
Place the rubber cushion over the end of the
bolt.
7
Slide the unit into the dashboard until a click
sound is heard.
If the unit cannot fi t into the dashboard,
•
remove the mounting bracket on the
both side of the unit and replace them
with the supplied short mounting
brackets.
both side of the unit and replace them
with the supplied short mounting
brackets.
8
Attach the trim plate.
9
Reconnect the negative terminal of the car
battery.
Turn on
1
Press the to turn on the unit.
The screen opens automatically.
»
The available OSD (On-Screen Display)
»
languages are displayed.
languages are displayed.
2
Touch a language to select.
The OSD language is changed to the
»
selected language immediately.
selected language immediately.
To adjust the screen tilt, press
•
TILT .
To close the screen, press
•
OPEN/CLOSE .
To adjust the brightness/contrast, press
•
/ ,
then adjust 4 WAY NAVIGATION .
To turn off the system, press
To turn off the system, press
•
for 3 sec-
onds.
The screen closes automatically.
»
Set clock
1
Touch to display main menu.
2
Touch
[Setting].
The setup menu is displayed.
»
3
Touch
[General].
4
Touch
the
[Clock mode] repeatedly to
select:
[12hr]
•
: 12 hour mode
[
•
24hr] : 24 hour mode
5
Touch the hour digits, then touch or .
6
Touch the minute digits, then touch or .
7
If 12 hour mode is selected, touch or
to select AM or PM .
8
Touch
to exit.
Tune to a radio station
1
Touch
to display the main menu.
2
Touch
[Radio].
Band and frequency information is
»
displayed.
displayed.
3
Touch
[Band] repeatedly to select:
FM band options:
•
FM1, FM2, FM3
AM band options:
•
AM1, AM2
4
Briefl y touch [Previous] or [Next] to tune
to a radio station by step.
Play discs
1
Insert the disc into the disc slot with label
side facing up.
Play starts automatically.
»
To remove the disc, press the
»
button.
When the disc is ejected, the unit switches
»
to the previous source, if connected. Other-
wise, the unit switches to [Radio] mode auto-
matically.
to the previous source, if connected. Other-
wise, the unit switches to [Radio] mode auto-
matically.
Insert USB or SD/MMC card
1
Open the USB/SD/MMC card cover.
2
Insert the USB device or SD/MMC card into
the USB socket or SD/MMC card slot.
Play starts automatically.
»
Pair the Bluetooth-enabled
devices
1
Turn on the Bluetooth function on the
device.
2
Setup the Bluetooth function on your device.
3
Select “CED750” in the pairing list.
4
Enter default password “0000”.
iI pairing succeeds.
»
[Connect] is displayed
on the panel.
Make a call
1
Pair the phone with the system.
2
Touch
to return to main menu.
3
Touch
[Bluetooth].
The Bluetooth menu is displayed.
»
4
Touch
to dial.
Receive call
1
If there is incoming call, [Incoming call…]
fl ashes on the screen. Speak into the Blue-
tooth microphone.
tooth microphone.
2
When conversation ends, touch to
terminate the call.
3
Prin
tin
g in
C
hin
a
Prin
tin
g in
C
hin
a
4
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
CED750 QSG_Eng.indd 2
CED750 QSG_Eng.indd 2
2008-12-12 16:05:30
2008-12-12 16:05:30