Land Pride RCF2784 Benutzerhandbuch
18
Section 1: Assembly & Set-up
RCF2784 Rotary Cutters 326-364M
12/15/15
Hydraulic Hook-up
!
DANGER
Refer to Figure 1-12 on page 17:
1.
1.
Make sure spring support loop (#14) is securely
fastened to the hitch frame and fastener hardware is
properly tightened.
fastened to the hitch frame and fastener hardware is
properly tightened.
2.
Route cylinder hose (#9) through spring support loop
(#14) and connect to tractor remote outlet. Do set
tractor control lever in float position.
(#14) and connect to tractor remote outlet. Do set
tractor control lever in float position.
3.
Check driveline for adequate clearance under all
ranges of cutter height.
ranges of cutter height.
a. With driveline shaft attached to the tractor, slowly
raise and lower cutter to its upper and lower limits
while observing clearances between hitch and
driveline.
while observing clearances between hitch and
driveline.
b. Adjust tractor drawbar height and/or length if
driveline interferes. See Figure 1-11 on page 17 for
correct drawbar dimensions.
correct drawbar dimensions.
4.
Cycle hydraulic system by extending and retracting
lift cylinder several times. It may be necessary to
purge the hydraulic system of trapped air if operation
is sluggish. See “Purge Hydraulic System” below.
lift cylinder several times. It may be necessary to
purge the hydraulic system of trapped air if operation
is sluggish. See “Purge Hydraulic System” below.
Purge Hydraulic System
!
DANGER
1.
With deck skid shoes resting firmly on the ground,
shut tractor off, and move hydraulic control lever back
and forth to relieve all hydraulic pressure in the
hydraulic system.
shut tractor off, and move hydraulic control lever back
and forth to relieve all hydraulic pressure in the
hydraulic system.
2.
Loosen hydraulic hose fitting at the hydraulic cylinder
slightly to allow air and fluid to escape.
slightly to allow air and fluid to escape.
3.
Restart tractor and slowly activate tractor control
lever to extend and retract hydraulic cylinder to purge
trapped air from the hydraulic system.
lever to extend and retract hydraulic cylinder to purge
trapped air from the hydraulic system.
4.
Lower cutter down until deck skid shoes are resting
firmly on the ground, shut tractor off, and move
hydraulic control lever back and forth to relieve all
hydraulic pressure in the hydraulic system.
firmly on the ground, shut tractor off, and move
hydraulic control lever back and forth to relieve all
hydraulic pressure in the hydraulic system.
5.
After all air is purged from the hydraulic system and
all hydraulic pressure is relieved, retighten hose
fitting at the hydraulic cylinder.
all hydraulic pressure is relieved, retighten hose
fitting at the hydraulic cylinder.
Assembly of Optional Guards
!
DANGER
Front Rubber Guard
Refer to Figure 1-13:
1.
Install Front Rubber Guards (#1 & #2) as shown with
3/8"-16 x 1" GR5 carriage bolts (#3), and hex whiz
nuts (#4).
3/8"-16 x 1" GR5 carriage bolts (#3), and hex whiz
nuts (#4).
2.
Tighten nuts to the correct torque.
Front Rubber Guard Option
Figure 1-13
Front Single or Double Chain Guard
Refer to Figure 1-14:
1.
Install front chain guards (#1 & #2) as shown with
3/8"-16 x 1" GR5 carriage bolts (#3), and hex whiz
nuts (#4).
3/8"-16 x 1" GR5 carriage bolts (#3), and hex whiz
nuts (#4).
2.
Tighten nuts to the correct torque.
Front Single Chain Guard Option
Figure 1-14
33028
33027