Snapper 331522KVE Benutzerhandbuch

Seite von 38
 
17 
Section 3 – MAINTENANCE 
 
WARNING 
DO NOT attempt any adjustments, maintenance, service 
or repairs with the engine running. Stop engine. Stop 
blade. Engage parking brake. Remove key. Remove 
spark plug wire from spark plug and secure away from 
plug. Engine and components are HOT. Avoid serious 
burns, allow all parts to cool before working on machine. 
Fuel Filler Cap and Vent must be closed securely to 
prevent fuel spillage. 
 
3.  Check fill/level plug for damage. If signs of wear or 
cracks are visible, replace plug with new plug. See 
Figure 3.9. 
4.  To check lubricant in chain case, remove fill/level 
plug and look for lubricant on the internal 
components of the chain case.  If no lubricant is 
visible, add SNAPPER transmission grease as 
needed.  See Figure 3.9.  
 
FIGURE 3.9 
 
 
3.3.10.   Check “MAINTENANCE SCHEDULE” Section 
of Engine Owner’s Manual for additional engine service. 
 
3.4  SERVICE - ANNUALLY 
3.4.1. ENGINE 
1.  
Perform all maintenance as specified in 
“MAINTENANCE SCHEDULE” Section of this manual. 
3.4.2. FUEL 
FILTER 
Service fuel filter as instructed below, on COLD ENGINE 
ONLY!  
 
IMPORTANT: To stop flow of fuel, tank may be removed from 
bracket and set on the floor so the fuel level will be below the 
filter. Refer to Section “REMOVING FUEL TANK”. 
1.  Remove hose clamps from fuel filter. 
2.  Remove fuel lines from filter. Discard filter. 
3.  Install new fuel filter. See Figure 3.10. 
4.  Reinstall fuel tank into bracket. 
5.  Carefully reinstall fuel clamps. 
6.  Check fuel system for leaks. 
 
 
 
 
FIGURE 3.10 
 
3.5
  EVERY TWO YEARS 
In addition to regular maintenance, the following 
components of the Rear Engine Rider should be 
carefully inspected every two years for wear or 
damage.  Replace worn or damaged parts with 
genuine SNAPPER replacement parts available 
from an authorized SNAPPER dealer. 
3.5.1.  All bushings and pivot areas. 
3.5.2.  Check both front wheel king pins. 
3.5.3.  Transmission shift lever and detent. 
3.5.4.  Clutch disc. 
3.5.5.  Clutch Yoke. 
3.5.6.  Mower deck linkage and pivot areas. 
 
3.6  STORAGE (OUT OF SEASON) 
If desired, the Rear Engine Rider can be stored on 
the rear bumper.  Perform the following procedures 
to insure the Rear Engine Rider will operate 
properly when taken out of storage. 
 
3.6.1.  Thoroughly clean the Rear Engine Rider by 
removing all grass clippings and debris. 
3.6.2. Perform maintenance and lubrication as 
required. 
3.6.3.  Drain fuel from fuel tank. 
3.6.4.  Start engine and allow it to run until engine 
runs out of fuel.  This allows the carburetor and fuel 
system to remain clean during storage. 
3.6.5.  Remove battery.  Refer to Section 
“BATTERY STORAGE”. 
3.6.6.  Close vent on fuel filler cap. 
3.6.7.  Carefully stand Rear Engine Rider on rear 
bumper in desired location for storage. 
 
 
 
AXLE 
BOOTS 
CHAIN 
CASE 
FILL/LEVEL 
PLUG 
P.N. 1-1024 
FUEL 
TANK 
FUEL 
FILTER 
HOSE 
CLAMPS 
P.N. 1-4359