Dixon ZTR 308 Benutzerhandbuch

 

IMPORTANT    -     READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS.

 

Seat Adjustment

 

Loosen bolts on sliding brackets under each side of the seat, slide seat forward or rearward  to 
desired position. Tighten bolts. Do not operate the mower with bracket bolts in "loose" 
condition.

 

Mower Blade Operation

 

To engage the mower blades, turn lever  on floor, slowly, to the "ON" position. To disengage 

mower blades, turn lever, slowly, to the "OFF" position.

 

Removing The Body

 

1. Disconnect Throttle cable from engine.

 

2. Disconnect the wiring loom from the body by  turning the threaded collar on the connector in a      

counterclockwise direction. This connector is located at the left rear of the body.

 

3. Remove four control lever bolts, and remove upper control levers, (P/N 9079 & 9080).

 

4. Remove the two attach nuts on the floor of the body and release the latches on the rear  of 

the body, near each side.

 

5. Place height adjustment lever in the vertical position, and mower deck engaging lever in 

(

        

the "OFF" position. Carefully lift the body off the chassis.

 

6. For assembly, reverse the procedure.

 

Removing The Mower Deck

 

1. Loosen the belt keeper, (P/N 2294), located under the engine by loosening two rear engine   

mounting bolts, allowing the deck drive belt to come free of the rear pulley. Tighten the belt 
keeper.

 

2. Disconnect the wiring loom at the deck safety switch, (P/N 4242).

 

3. Remove four attach pins, (P/N 6107) and clips, (P/H 3072) from the deck attach points and 

stabilizer bars.

 

4. Lift the front of the mower chassis clear of the deck engaging rod, (P/N 2686). Roll the chassis free 

of the deck.

 

5. 'To install, reverse the procedure.

 

Adjustment Of Mower Deck Drive Belt

 

 

1. Disengage the mower deck drive belt.

 

2. To obtain the proper belt tension, loosen lock nut, (P/N 3005) and rotate engaging rod  ' 

linkage, (P/N 3607).

 

3. After making an adjustment, engage the drive belt and check the tension. (The proper  • 

tension for an engaged V-belt is the lowest tension a t which the belt will not slip under 
normal load conditions.)

 

4. If further adjustment is necessary, repeat steps 1 through 3, until proper adjustment is 

achieved.

 

5. After the belt tension is adjusted, check to assure that the mower blade  will  not turn 

freely when the engaging rod is in the "OFF" position.

 

6. If the mower blade turns freely, adjust the blade brake using swivel fitting, (P/N 2172),  located 

on the brake linkage "L" rod, (P/N 2841) so that there is 1/8" to 1/4" gap between the deck safety 

switch body, (P/N 4242), and the striker plate, attached to the clutch idler bracket, (P/N 2847), 
when the brake is engaged.

 

NOTE: The clutch idler bracket, (P/N 2847) must be raised so that the brake link  swivel, (P/N 2172) can 

be adjusted.

 

7. After adjustment is achieved, perform the safety checks listed below.

 

"IMPORTANT" - Perform SAFETY CHECKS after making any repairs or adjustments.

 

1. After reassembly, while seated on the mower, attempt to start the engine with the mower deck 

engaged. Engine should not start. If engine does start, return the mower to an Authorized Dixon 
Dealer for adjustment or repair.

 

2. Disengage the mower deck and start engine. With the operator in the normal seated position, engage 

mower deck and remove weight from the seat. The engine should stop. If the engine doesn't stop when 
operator rises fr om the seat, return the mower to an Authorized Dixon Dealer for adjustment or 

repair.

 

3. Engage, then disengage, mower blade in each cutting height. Insure that blade disengages and comes 

to a stop within 5 seconds in each height position. If blade does not disengage properly, repeat 
belt adjustment procedure or contact your Authorized Dixon Dealer.

 

Removing The Mower Blade

 

Secure the blade, (P/N 6013) from turning. (Observe the blade position when removing.) Remove

 

the blade bolt from the center of the blade, remove the blade flange, (P/N 2837), blade, (P/N 2406),

 

and spacer, (P/N 2829).

 

W A R N I N G :         Sharp edges on  the blade can cause injury!    Caution should be  e x e r c i s e d  when  s e r v i c e

 

is required on the blade.

 

Parking Brake Adjustment

 

Remove the body as described above.    Tighten nut on brake rod,   (P/N 2533), (Located in front of

 

the transaxle on each s i d e ) , ju s t  enough to prevent brake from slipping when engaged.

 

CAUTION;    Over-tightening may cause premature wear on the brake band, (P/N 5085).

 

 

 

 

 

DATE   8/86  Re 
PAGE    1  of  6  

 

P/N 8603