Dixon ZTR 310 Benutzerhandbuch

.IMPORTANT  - READ OPERATOR'S MANUAL BEFORE OPERATION.  

Seat Adjustment 

Loosen Bolts on sliding brackets under each side of seat, slide seat forward  or rearward to desired position.    
Re-tighten bolts.    Do not operat e mower with  bracket bolts in a loose condition. 

Mower Blade Operation 

To start mower blades, move lever on floor slowly to "ENGAGE" position.  To stop mower blades, 
move lever on floor slowly to "DISENGAGE" position. 

Body Removal 

1.    Disconnect throttle cable from engine. 
2.    Disconnect the rear wiring loom (P/N 4109) from the body by lightly squeezing the Econo-Seal plug.   This 

Is located at the left rear of the body. 

3.    Note:    Loosen bolts that hold body switch (P/N 4079) and slide switch away  from engaging rod.    Tighten one 

bolt just enough to hold switch 1n this position until body is reassembled. 

4.    Remove 4 control lever bolts and remove upper control levers (P/N 1689 i 1690). 
5.    Remove engaging handle (P/N 6089) by removing bolt and nut under handle. 
6.    Remove the 2 attach nuts on floor of body and 2 sheet metal screws at the  rear of body. 
7.     Place height adjustment lever i n vertical position, engage parking brake and carefully lift body up and 

off chassis. 

8.    Reverse the above procedure for assembly. 

Safety Checks 

With the mower deck in the engaged position slide the body switch (P/N 4079) toward 
the engaging rod (P/N 6038)      until the switch leaf just makes contact with the 
s w i t c h button.    Tighten both bolts 1n switch bracket. 
with mower deck engaged, attempt to start engine in all cutting height positions.  
if engine starts in any cutting height position, re-adjust the switch.    Disengage 
the mower deck and start the engine In each cutting height position.    If engine 
fails to start in any cutting height position, re-adjust switch. 
with operator in normal mowing position, engage mower deck and remove weight from 
seat.    The engine should stop.    Repeat this procedure in each cutting height  
position.    If engine does  not stop when operator rises from seat in each cutting 
height position, return to an authorized Dixon dealer for adjustment or repairs. 

Parking Brake Adjustment 

Remove body as described above.    Tighten nut on brake rod (P/N2533) (Located 1n  front of the transaxle on 
each side.), just enough to prevent brake from slipping when engaged.  CAUTION:    Over tightening may 
cause premature wear on brake band (P/N 5085). 

Mower Drive Belt Adjustment 

Belt tension for mower drive belt (P/N 2412) is adjusted by loosening nut on the connecting arm assembly 
(P/N 2148)    and turning bolt to achieve desired tension.  Re-tighten nut.    Tension should be checked with 
belt 1n engaged position. 

Removing Mower Deck 

1.    Remove engaging handle (P/N 6089) by removing bolt and n ut under handle. 
2.    Loosen belt keeper (P/N 2234) located under engine by loosening 2 rear engine mount bolts to allow mower 

deck drive belt to come free of rear pulley. Re-tighten belt keeper. 

3.    Remove 4 attach pins (P/N 6107) and clips fro* 4 mower deck attach points and 2 stabilizer bars (P/N 6159). 
4.    Raise front of mower chassis to allow mower deck engaging rod (P/N 6038) to clear the c h a s s i s .     At this time, 

mower may be rolled free of mower deck  for  s e r v i c e and/or replacement. 

5.    To re-install, reverse the above procedure. 

Removing Hower Cutter Blade 

Secure mower cutter blade (P/N 2406) from turning (observe blade position when removing) remove blade bolt 
from center of blade. 

 

DIXON

  

INDUSTRIES,

 

INC.

 

BOX

494

 

COFFEYVILLE,

  

KANSAS

  

67337-0494

   

(316)

 

251-2000 

P/N 8536  (H/83)