Troy-Bilt 1030 Benutzerhandbuch
7
8.
If the wheels can still be turned when you engage
the drive control, loosen the jam nut on the drive
cable and thread the cable in one turn. Recheck the
adjustment and repeat if needed.
the drive control, loosen the jam nut on the drive
cable and thread the cable in one turn. Recheck the
adjustment and repeat if needed.
9.
Tighten the jam nut to secure the cable when
correct adjustment is reached.
correct adjustment is reached.
NOTE: For further details, refer to the Adjustment
section on page 17.
section on page 17.
Shear Pin Storage
An area for convenient shear pin storage is located
under the plastic dash panel. See Figure 6.
under the plastic dash panel. See Figure 6.
Figure 6
Skid Shoe
Locate the shave plate and the skid shoes in Figure 8
on page 8. The space between this shave plate and
the ground can be adjusted. For close snow removal,
place skid shoes in the low position. Use middle or
high position when area to be cleared is uneven.
on page 8. The space between this shave plate and
the ground can be adjusted. For close snow removal,
place skid shoes in the low position. Use middle or
high position when area to be cleared is uneven.
IMPORTANT:
It is not recommended that you operate
this snow thrower on gravel as loose gravel can be
easily picked up and thrown by the auger causing
personal injury or damage to the snow thrower.
easily picked up and thrown by the auger causing
personal injury or damage to the snow thrower.
If for some reason, you have to operate the snow
thrower on gravel, keep the skid shoe in the highest
position for maximum clearance between the ground
and the shave plate.
thrower on gravel, keep the skid shoe in the highest
position for maximum clearance between the ground
and the shave plate.
1.
Adjust skid shoes by loosening the four lock nuts
and carriage bolts and moving skid shoes to
desired position. See Figure 7.
and carriage bolts and moving skid shoes to
desired position. See Figure 7.
2.
Make certain the entire bottom surface of skid
shoes are against the ground to avoid uneven wear
on the skid shoes.
shoes are against the ground to avoid uneven wear
on the skid shoes.
3.
Tighten nuts and bolts securely.
Figure 7
Tire Pressure (Pneumatic Tires)
The tires are over-inflated for shipping purposes.
Check the tire pressure before operating the snow
thrower. Refer to the tire side wall for tire
manufacturer’s recommended psi and deflate (or
inflate) the tires as necessary.
Check the tire pressure before operating the snow
thrower. Refer to the tire side wall for tire
manufacturer’s recommended psi and deflate (or
inflate) the tires as necessary.
NOTE: If the tire pressure is not equal in both tires, the
unit may pull to one side or the other and the shave
plate will not sit level on the ground.
unit may pull to one side or the other and the shave
plate will not sit level on the ground.
WARNING:
Under any circumstance do not
exceed manufacturer’s recommended psi.
Equal tire pressure should be maintained at all
times. Excessive pressure when seating
beads may cause tire/rim assembly to burst
with force sufficient to cause serious injury.
Refer to sidewall of tire for recommended
pressure.
Equal tire pressure should be maintained at all
times. Excessive pressure when seating
beads may cause tire/rim assembly to burst
with force sufficient to cause serious injury.
Refer to sidewall of tire for recommended
pressure.
Four-Way Chute Control™
The chute control lever may need to be lubricated to
reduce its break-in period. Vegetable oil, petroleum jelly
or motor oil can be used as lubricant.
reduce its break-in period. Vegetable oil, petroleum jelly
or motor oil can be used as lubricant.
IMPORTANT:
This unit is shipped with engine oil in the
engine, but without gasoline. After assembly, see
OPERATION section of this manual for fuel selection
and fill-up.
OPERATION section of this manual for fuel selection
and fill-up.
High Position
Low Position
Middle Position
Lock Nut
Skid Shoe