Roland MC-909 Benutzerhandbuch
146
Expanding the Memory
The MC-909 comes with 16 MB of memory into which audio samples
can be loaded. However, in some cases, 16 MB of memory will be
insufficient for loading large amounts of data. In such a case, you
will have to add separately sold memory (DIMM). Memory can be
expanded up to 256 MB.
can be loaded. However, in some cases, 16 MB of memory will be
insufficient for loading large amounts of data. In such a case, you
will have to add separately sold memory (DIMM). Memory can be
expanded up to 256 MB.
Before expanding the memory, consult with your retailer, the nearest
Roland Service Center, or an authorized Roland distributor.
Roland Service Center, or an authorized Roland distributor.
Precautions for Expanding
Memory
901
• To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the following
whenever you handle the board.
whenever you handle the board.
1
• Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been discharged.
electricity you might have been carrying has been discharged.
2
• When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
5
• Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
transport it.
• Use a Philips screwdriver that is suitable for the size of the screw
(a number 2 screwdriver). If an unsuitable screwdriver is used,
the head of the screw may be stripped.
the head of the screw may be stripped.
• To remove a screw, rotate the screwdriver counter-clockwise. To
tighten the screws, rotate the screwdriver clockwise.
fig.Screw.e
• Be careful that the screws you remove do not drop into the
interior of the MC-909.
• Be careful not to cut your hand on the edge of the cover or the
opening edge while removing the cover.
911
• Do not touch any of the printed circuit pathways or connection
terminals.
912
• Never use excessive force when installing a circuit board. If it
doesn’t fit properly on the first attempt, remove the board and try
again.
again.
913
• When circuit board installation is complete, double-check your
work.
914 (Modified)
• Always turn the unit off and unplug the power cord before
attempting installation of the memory DIMM board.
915 (Modified)
• Install only the specified memory DIMM board. Remove only the
928
• When turning the unit upside-down, get a bunch of newspapers
or magazines, and place them under the four corners or at both
ends to prevent damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or controls get
damaged.
ends to prevent damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or controls get
damaged.
929
• When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
• Do not leave the bottom cover removed. After installation of the
memory module is complete, be sure to replace the cover.
How to Expand the Memory
Install the memory module after removing the bottom panel cover.
1.
Before expanding the memory, turn off the power of the MC-909
and all connected devices, and disconnect all cables, including
the Power cable, from the MC-909.
and all connected devices, and disconnect all cables, including
the Power cable, from the MC-909.
2.
Turn the MC-909 over, remove the screws indicated in the
following diagram, and remove the cover.
following diagram, and remove the cover.
fig.Exp-01.e_90
3.
Press outward the white clips at either end of the socket should
be in the downward position.
be in the downward position.
fig.DIMM-01
tighten
loosen
Screws to be removed
MC-909_Ref_e.book 146 ページ ２００５年３月１日 火曜日 午後３時２９分