Roland XP-30 Benutzerhandbuch
132
Chapter 6. Getting the Full Potential of the XP-30
Using External MIDI Devices
■
Using the XP-30 to Control
External MIDI Devices
1. Use a MIDI cable to connect the MIDI OUT connector of the
XP-30 to the MIDI IN connector of the external MIDI device.
fig.6-01.e
2. Set the XP-30’s transmit channel to match the external
MIDI device’s receive channel.
The transmit channel is determined by the following
parameters.
- Patch mode
Tx-Ch parameter (SYSTEM/MIDI/PATCH MIDI)
- Performance mode
Channel parameter (PERFORM/MIDI/MIDI)
Turn the Tx parameter (PERFORM/MIDI/MIDI) to ON.
parameters.
- Patch mode
Tx-Ch parameter (SYSTEM/MIDI/PATCH MIDI)
- Performance mode
Channel parameter (PERFORM/MIDI/MIDI)
Turn the Tx parameter (PERFORM/MIDI/MIDI) to ON.
3. If you want to play only the sound source of the external
MIDI device, set the Local parameter (SYSTEM/MIDI/
PATCH MIDI) / (SYSTEM/MIDI/PERFORM MIDI) to OFF.
PATCH MIDI) / (SYSTEM/MIDI/PERFORM MIDI) to OFF.
If you wish to connect two or more external MIDI devices,
use the MIDI THRU connector of the external MIDI device.
use the MIDI THRU connector of the external MIDI device.
fig.6-02.e
* If you “daisy-chain” three or more MIDI devices using IN
→
THRU
→
IN
→
THRU ..., the MIDI signal may become
garbled, and data errors may occur. In such cases, use a MIDI
Thru Box. MIDI Thru Boxes are devices that allow a single
stream of MIDI data to be sent to a large number of MIDI
devices without causing data errors.
Thru Box. MIDI Thru Boxes are devices that allow a single
stream of MIDI data to be sent to a large number of MIDI
devices without causing data errors.
■
Playing the XP-30’s Sound
Source from an External MIDI
Device
1. Use a MIDI cable to connect the external MIDI device’s
MIDI OUT connector to the XP-30’s MIDI IN connector.
fig.6-03.e
2. Set the XP-30’s receive channel to match the external
MIDI device’s transmit channel.
The receive channel is determined by the following
parameters.
- Patch mode
Rx-Ch parameter (SYSTEM/MIDI/PATCH MIDI)
- Performance mode
Channel parameter (PERFORM/MIDI/MIDI)
Turn the Rx parameter (PERFORM/MIDI/MIDI) to ON.
parameters.
- Patch mode
Rx-Ch parameter (SYSTEM/MIDI/PATCH MIDI)
- Performance mode
Channel parameter (PERFORM/MIDI/MIDI)
Turn the Rx parameter (PERFORM/MIDI/MIDI) to ON.
■
Selecting XP-30 Sounds from
an External MIDI Device
By transmitting Bank Select messages (controller number 0
and 32) and Program Change messages from the external
MIDI device to the XP-30, you can select Patches,
Performances, or Rhythm Sets. In other words, when you
select sounds on an external MIDI keyboard, the
corresponding MIDI message will be transmitted to the XP-
30, causing the XP-30 to select the appropriate Patch, etc.
and 32) and Program Change messages from the external
MIDI device to the XP-30, you can select Patches,
Performances, or Rhythm Sets. In other words, when you
select sounds on an external MIDI keyboard, the
corresponding MIDI message will be transmitted to the XP-
30, causing the XP-30 to select the appropriate Patch, etc.
* If the XP-30 receives only Program Change messages without
receiving Bank Select messages, it will select sounds only from
the currently selected group such as PR-A or USER.
the currently selected group such as PR-A or USER.
MIDI OUT
MIDI IN
XP-30
MIDI Keyboard
MIDI IN
MIDI
THRU
MIDI IN
MIDI Keyboard
MIDI Keyboard
MIDI OUT
XP-30
MIDI IN
MIDI OUT
XP-30
MIDI Keyboard