Yamaha MG12XU/MG12 Benutzerhandbuch
MG20XU/MG20/MG16XU/MG16/MG12XU/MG12 Owner’s Manual
25
Controls and Connectors
r [STEREO OUT] jacks
These are XLR type and TRS phone-type balanced output
jacks that output the mixed stereo signal. The signal level is
adjusted by the [STEREO] master fader before it is output.
You can use these jacks, for example, to connect to the power
amplifier driving your main speakers.
jacks that output the mixed stereo signal. The signal level is
adjusted by the [STEREO] master fader before it is output.
You can use these jacks, for example, to connect to the power
amplifier driving your main speakers.
t [PHONES] jack
Connect a pair of headphones to this TRS phone jack.
NOTE
• The [PHONES] jack outputs the same signal as the [MONI-
TOR OUT] jacks.
• When the [PFL] indicator is flashing, the signal for channels
where the [PFL] switch is pressed is output. When the [PFL]
indicator is off, the signal for the buses selected in the [MON-
ITOR] section y is output.
indicator is off, the signal for the buses selected in the [MON-
ITOR] section y is output.
y [MONITOR] section
• [POWER] indicator
This indicator lights up when the mixer’s power is on
(
(
).
• Level meter
The level meter LED shows the level of the signal in
the STEREO L/R and GROUP buses, or selected with
[PFL] switches. The “0” (
the STEREO L/R and GROUP buses, or selected with
[PFL] switches. The “0” (
< ) segment corresponds to
the nominal output level. The level meter [PEAK] indi-
cator lights when output reaches the clipping level.
cator lights when output reaches the clipping level.
• [PFL] indicator
When the [PFL] switch is on, the indicator flashes.
• [MONITOR LEVEL] knob
For adjusting the level of the signal output to the
[MONITOR OUT] jack.
[MONITOR OUT] jack.
• [PHONES] knob
For adjusting the level of the signal output to the
[PHONES] jack.
[PHONES] jack.
• [SOURCE]/[SOURCE SELECT] (Monitor signal
selection switch)
Sets the signal sent to the [MONITOR OUT] jack,
[PHONES] jack, and level meter. You can use this
switch to select the signal from the STEREO L/R
buses, GROUP 1-2 buses, or GROUP 3-4 buses
(MG20XU/MG20/MG16XU/MG16).
[PHONES] jack, and level meter. You can use this
switch to select the signal from the STEREO L/R
buses, GROUP 1-2 buses, or GROUP 3-4 buses
(MG20XU/MG20/MG16XU/MG16).
• MG12XU/MG12
STEREO L/R buses: [STEREO] (
)
GROUP 1-2 buses: [GROUP] (
)
• MG20XU/MG20/MG16XU/MG16
STEREO L/R buses: [STEREO] (
)
GROUP 1-2 buses: [GROUP] (
), [1-2] (
)
GROUP 3-4 buses: [GROUP] (
), [3-4] (
)
PHONES
MONITOR
PF
L L
PF
L R
PFL
C
TRL
STR MONI
STL MONI
G2 MONI
G3 MONI
G4 MONI
G1 MONI
MG20XU/MG20
MG16XU/MG16
MG16XU/MG16
MG12XU/
MG12
1-2/3-4
STEREO/
GROUP
GROUP
POWER
PEAK
+10
+6
+3
+3
0
-3
-6
-6
-10
-15
-20
-25
-15
-20
-25
PFL
-30
PHONES
[3mW 40ohms]
[3mW 40ohms]
MONITOR OUT L
[+4dBu]
[+4dBu]
MONITOR OUT R
[+4dBu]
[+4dBu]
MG20XU/MG20
MG16XU/MG16
MG12XU/MG12