Roland SP-555 Benutzerhandbuch
68
Appendix
If you connect a pedal switch (DP series; sold separately) to the rear panel PEDAL jack, you’ll be able to perform the following
operations by pressing the pedal.
operations by pressing the pedal.
1.
Using the screws located on the bottom of the SP-555,
attach the stand holder of the PDS-10 pad stand (sold
separately) as shown in the illustration.
attach the stand holder of the PDS-10 pad stand (sold
separately) as shown in the illustration.
* You must use these screws. Using any other screws will cause
malfunctions.
When turning the unit upside-down, get a bunch of
newspapers or magazines, and place them under the four
corners or at both ends to prevent damage to the buttons and
controls. Also, you should try to orient the unit so no buttons or
controls get damaged.
newspapers or magazines, and place them under the four
corners or at both ends to prevent damage to the buttons and
controls. Also, you should try to orient the unit so no buttons or
controls get damaged.
When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
dropping it, or allowing it to fall or tip over.
2.
Attach the SP-555 to the PDS-10 pad stand.
For details on assembling the pad stand or attaching the
stand holder, refer to the owner’s manual of the pad
stand.
stand holder, refer to the owner’s manual of the pad
stand.
If you attach the SP-555 to the PDS-10, you must spread the
legs of the PDS-10 to their full extent. You must set up the stand
so that the total height including the SP-555 itself does not
exceed one meter.
legs of the PDS-10 to their full extent. You must set up the stand
so that the total height including the SP-555 itself does not
exceed one meter.
This stand for use only with specific Roland musical
instruments. See apparatus instructions. Use with other
models is capable of resulting in instability causing possible
injury.
instruments. See apparatus instructions. Use with other
models is capable of resulting in instability causing possible
injury.
About the pedal
Function
Action
Operation
REC/OVERDUB/PLAY
loop capture
loop capture
Press the pedal to cycle through the choices,
which are: record
which are: record
➜
play
➜
overdub
➜
play.
Rapidly press the pedal twice to stop.
While holding down [CANCEL], press the pedal
➜
turn the CTRL 3 knob
to get the display to indicate “LC.1.” Press [SAMPLING] to confirm.
PLAY/STOP loop cap-
ture
ture
Press the pedal to cycle through the choices,
which are: play
which are: play
➜
stop
➜
play.
While holding down [CANCEL], press the pedal
➜
turn the CTRL 3 knob
to get the display to indicate “LC.2.” Press [SAMPLING] to confirm.
PLAY/STOP pattern se-
quencer
quencer
Press the pedal to cycle through the choices,
which are: play
which are: play
➜
stop
➜
play.
While holding down [CANCEL], press the pedal
➜
turn the CTRL 3 knob
to get the display to indicate “SEq.” Press [SAMPLING] to confirm.
Turn FIXED VELOCITY
on/off
on/off
Press the pedal to toggle between on/off for
FIXED VELOCITY.
FIXED VELOCITY.
While holding down [CANCEL], press the pedal
➜
turn the CTRL 3 knob
to get the display to indicate “VEL.” Press [SAMPLING] to confirm.
Turn the effect on/off
Press the pedal to turn the effect on/off.
While holding down [CANCEL], press the pedal
➜
turn the CTRL 3 knob
to get the display to indicate “EF.S.” Press [SAMPLING] to confirm.
Attaching the stand (sold separately)
SP-555_e.book 68 ページ ２００７年６月２５日 月曜日 午前９時９分