Korg PA50 Benutzerhandbuch

Pitch/Phase Mod.

The following is an example of fade-in where the LFO
speed is increased from “1.0Hz” to “4.0Hz” when a note-
on message is received.
“AUTOFADE Src”=Gate1, “LFO Frequency [Hz]”=1.0
“LFO Frequency Mod”=AUTOFADE, “Amt”=3.0

The effect is off when a value for the dynamic modulation 
source specified for the “AUTOFADE Src” parameter is smaller 
than 64, and the effect is on when the value is 64 or higher. The 
AutoFade function is triggered when the value changes from 63 
or smaller to 64 or higher.

This stereo chorus/flanger effect enables you to control the
LFO speed and effect balance using auto fade, and you can
spread the sound by offsetting the phase of the left and right
LFOs from each other.

This effect resonates the input signal at a specified pitch. You
can set the pitch, output level, and pan settings for two reso-
nators individually. You can control the resonance intensity
via an LFO.

a

AUTOFADE Src

Off...Tempo

Selects the modulation source that starts AutoFade

☞

 Fx:027,

Rate
Sets the rate of fade-in

1...100

☞

 Fx:027

Fade-In Dly (Fade-In Delay) [msec]
Sets the fade-in delay time

00...2000msec

☞

 Fx:027

b

LFO Waveform
Selects LFO Waveform

Triangle, Sine

LFO Shape

–100...+100

Determines how much the LFO waveform is changed

☞

 Fx:020

c

LFO Phase [degree]

–180...+180

Sets the LFO phase difference between the left and right

☞

 Fx:010

d

LFO Frequency Mod

D-mod, AUTOFADE

Switches between D-mod and AUTOFADE for the LFO frequency modula-
tion  

☞

 Fx:027

e

LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

Src
Selects the modulation source of LFO speed

Off...Tempo

Amt

–20.00...+20.00Hz

Sets the modulation amount of LFO speed

f

L Delay Time [msec]
Sets the left channel delay time

0.0...500.0msec

R Delay Time [msec]
Sets the right channel delay time

0.0...500.0msec

g

Depth
Sets the depth of LFO modulation

0...200

h

Feedback
Sets the feedback amount

–100...+100

☞

 Fx:020

High Damp [%]

0...100%

Sets the feedback damping amount in the high range

☞

 Fx:020

i

Wet/Dry Mod

D-mod, AUTOFADE

Switches between D-mod and AUTOFADE for the effect balance modulation 

☞

 Fx:027

j

Wet/Dry

–Wet...–1:99, Dry, 1:99...Wet

 

☞

 Fx:010, 020,

Src

Off...Tempo

Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175

–100...+100

a

Control Mode

Manual, LFO, D-mod

Switches the controls of resonance intensity

☞

,

LFO/D-mod Invert

Off, On

Reverses the Voice 1 and 2 control when LFO/D-mod is selected

☞

b

LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

D-mod Src

Off...Tempo

Selects the modulation source that controls resonance intensity

c

Mod. Depth

–100...+100

Sets the amount of resonance intensity control via LFO/D-mod

Trim
Sets the input level at the resonator

0...100

d

Voice1: Pitch
Sets the voice1 Pitch for resonance

C0...B8

Fine [cent]

–50...+50

Fine-adjusts the voice 1 pitch for resonance

e

Voice1: Resonance

–100...+100

Sets the intensity of resonance when Control Mode = Manual

☞

High Damp [%]

0...100%

Sets the damping amount of resonant sound in the high range

☞

f

Voice1: Level
Sets the Voice1 output level

0...100

Pan
Sets the Voice1 stereo image

L6...R6

g

Voice2: Pitch
Sets the Voice2 Pitch for resonance

C0...B8

Fine [cent]
Fine-adjusts the voice 2 pitch for resonance

–50...+50

h

Voice2: Resonance

–100...+100

Sets the intensity of resonance when Control Mode = Manual

☞

High Damp [%]

0...100%

Sets the damping amount of resonant sound in the high range

☞

i

Voice2: Level
Sets the Voice2 output level

0...100

Pan
Sets the Voice2 stereo image

L6...R6

+