Avaya S8300 Benutzerhandbuch
5
Upgrading an Existing G700 with an S8300 — R1.x to R2.0
Upgrade the Firmware on the G700
Upgrade the Firmware on the G700
252
Installation and Upgrades for G700 and S8300
December 2003
Show MG List_Config
3
Refer to the list to check the FW vintage number of the G700. In the TYPE column, find G700,
then check the matching field in the FW VINTAGE column to see if it matches the vintage
number in your planning forms. If not, you must install new firmware on the G700 Media
Gateway. Also check if the release number in the FW VINTAGE column contains (A) or (B) to
designate the software bank. If the list shows B, you will upgrade A. If the list shows A, you will
upgrade B.
then check the matching field in the FW VINTAGE column to see if it matches the vintage
number in your planning forms. If not, you must install new firmware on the G700 Media
Gateway. Also check if the release number in the FW VINTAGE column contains (A) or (B) to
designate the software bank. If the list shows B, you will upgrade A. If the list shows A, you will
upgrade B.
4
Refer to the VOIP FW column and row for slot V0 (same row occupied by the G700 information)
to see if the number matches the VoIP firmware identified in your planning forms. If not, you
must also upgrade the G700 Media Gateway motherboard VoIP module.
to see if the number matches the VoIP firmware identified in your planning forms. If not, you
must also upgrade the G700 Media Gateway motherboard VoIP module.
NOTE:
The VoIP processor on the motherboard is upgraded using the same firmware image file
as the VoIP media modules; for example, the file mm760v8.fdl is vintage #8.
as the VoIP media modules; for example, the file mm760v8.fdl is vintage #8.
5
Check the FW VINTAGE column for vintages of each of the installed Media Modules: MM710,
MM711, MM712, MM720, and/or MM760 to see if they match the FW vintages in the planning
forms. If not, you must upgrade them, as well.
MM711, MM712, MM720, and/or MM760 to see if they match the FW vintages in the planning
forms. If not, you must upgrade them, as well.
Install New Firmware on the P330 Stack
Processor
Processor
Install P330 stack processor firmware
1
From your S8300 telnet session, telnet back to the P330 stack processor:
Type
telnet <xxx.xxx.xxx.xxx>
, where <xxx.xxx.xxx.xxx> is the IP address of the P330 stack
master processor on the customer’s LAN.
1
At the P330-1(configure)# prompt, type
copy tftp SW_image <file> EW_archive <ew_file> <tftp_server_address>
<Module#>
where
<file> is the full-path name for the image file with format and vintage number similar to
viisa3_8_2.exe,
<file> is the full-path name for the image file with format and vintage number similar to
viisa3_8_2.exe,
<ew_file> is the full-path name for the embedded web application file with format similar to
p330Tweb.3.8.6.exe,
p330Tweb.3.8.6.exe,
<tftp_server_ip_address> is the IP address of the TFTP server, and
eyp
SLOT TYPE CODE
SUFFIX HW
VINTAGE FW
VINTAGE VOIP
FW
---- ------
----- ------ ---------- ---------- -------
V0 G700 DAF1 A
00
210(B)
2
V1 ICC S8300
A
72
00
N/A
V2 DCP MM712
A
2
52
N/A
V3 ANA MM711
A
2
12
N/A
V4 DS1 MM710
A
1
54
N/A