Harman MPMI Benutzerhandbuch
36
Soundcraft MFXi MPMi User Guide Issue 1210
Reverse Reverb
Reverse reverb works in the opposite fashion from normal reverb. Whereas a normal reverb has the loudest
series of reflections heard first that then become quieter over time, the Reverse reverb has the softest reflec-
tions (essentially the tail of the reverb) heard first, and then grows louder over time until they abruptly cut off.
Reverse reverb works in the opposite fashion from normal reverb. Whereas a normal reverb has the loudest
series of reflections heard first that then become quieter over time, the Reverse reverb has the softest reflec-
tions (essentially the tail of the reverb) heard first, and then grows louder over time until they abruptly cut off.
Ambience Reverb
Ambience is used to simulate the effect of a small or medium sized room without noticeable decay. It is often
used for voice, guitar or percussion.
Ambience is used to simulate the effect of a small or medium sized room without noticeable decay. It is often
used for voice, guitar or percussion.
Studio Reverb
Much like Room reverb, Studio produces an excellent simulation of smaller, well controlled acoustic spaces,
characteristic of the main performance areas in recording studios. Studio is also useful with dialog and
voiceover applications as well as individual instrument and electric guitar tracks.
Much like Room reverb, Studio produces an excellent simulation of smaller, well controlled acoustic spaces,
characteristic of the main performance areas in recording studios. Studio is also useful with dialog and
voiceover applications as well as individual instrument and electric guitar tracks.
Arena Reverb
Arena reverb emulates a huge physical space such as an indoor sports venue or stadium. The characteristics
of Arena reverb are long secondary reflection times and a reduced amount of high frequency content. Arena
is a mostly mid- and low frequency dominant reverb, and is an ideal selection for “special effect” type ap-
plications that require extremely long reverb times. It is not a good choice for a very busy mix, since it can
reduce intelligibility.
Arena reverb emulates a huge physical space such as an indoor sports venue or stadium. The characteristics
of Arena reverb are long secondary reflection times and a reduced amount of high frequency content. Arena
is a mostly mid- and low frequency dominant reverb, and is an ideal selection for “special effect” type ap-
plications that require extremely long reverb times. It is not a good choice for a very busy mix, since it can
reduce intelligibility.
Spring Reverb
A Spring reverb is created by a pair of piezoelectric crystals—one acting as a speaker and the other acting as
a microphone— connected by a simple set of springs. The characteristic ‘boing’ of a spring is an important
component of many classic rock and rockabilly guitar sounds.
A Spring reverb is created by a pair of piezoelectric crystals—one acting as a speaker and the other acting as
a microphone— connected by a simple set of springs. The characteristic ‘boing’ of a spring is an important
component of many classic rock and rockabilly guitar sounds.
KARAOKE
The Golden Karaoke Patch creates a great Karaoke performance sound in any size KTV room.
The Golden Karaoke Patch creates a great Karaoke performance sound in any size KTV room.
REVERB CONTROLS
Pre Delay
Creates an additional time delay between the source signal and the onset of reverberation. This control is not
intended to precisely mimic the time delays in natural spaces, as the build-up of reverberation is gradual,
and the initial time gap is usually relatively short. For the most natural effect, the Pre Delay values should be
set in the range of 10-25 milliseconds. However, if a mix is very busy or overly cluttered, increasing the Pre
Delay time may help clarify it, and set each instrument apart from each other.
Creates an additional time delay between the source signal and the onset of reverberation. This control is not
intended to precisely mimic the time delays in natural spaces, as the build-up of reverberation is gradual,
and the initial time gap is usually relatively short. For the most natural effect, the Pre Delay values should be
set in the range of 10-25 milliseconds. However, if a mix is very busy or overly cluttered, increasing the Pre
Delay time may help clarify it, and set each instrument apart from each other.
Decay
Controls the amount of time the reverb can be heard. Higher settings increase reverberation times which are
usually associated with larger acoustical environments, but can decrease intelligibility. Lower settings shorten
reverb times and should be used when a smaller apparent space or a more subtle effect is desired.
Controls the amount of time the reverb can be heard. Higher settings increase reverberation times which are
usually associated with larger acoustical environments, but can decrease intelligibility. Lower settings shorten
reverb times and should be used when a smaller apparent space or a more subtle effect is desired.
Liveliness
Adjusts the amount of high frequency content in the reverberation tails. Higher settings increase high frequency
response, creating brighter reverbs; lower settings create darker reverbs with more bass frequency emphasis.
Adjusts the amount of high frequency content in the reverberation tails. Higher settings increase high frequency
response, creating brighter reverbs; lower settings create darker reverbs with more bass frequency emphasis.