Epson EPL-6200 Benutzerhandbuch
EPSON EPL-6200/EPL-6200L
Revision A
Product Description
Control Panel (EPL-6200L)
53
“Near Buffer Full”. The Continue command of the ESCPAGES-02 protocol
releases the error, and printing resumes from the next page. When “Auto
Continue = ON”, the printer displays the “Print Failure” warning instead of
this error, and resumes printing the next page.
releases the error, and printing resumes from the next page. When “Auto
Continue = ON”, the printer displays the “Print Failure” warning instead of
this error, and resumes printing the next page.
Remedy
To print pages after “Mem Overflow”, select [Continue] on the EPSON Status
Monitor.
To reprint after modifying driver settings, select [Cancel Printing] on the
EPSON Status Monitor.
To print pages after “Mem Overflow”, select [Continue] on the EPSON Status
Monitor.
To reprint after modifying driver settings, select [Cancel Printing] on the
EPSON Status Monitor.
1.6.3.4 Details of Warning Status and Processing
Multi Copy Error
Description
Band data of the page for multi-copying has not been saved for one page
completely.
This warning is cleared by the ResetFlag command of the ESCPAGES-02
protocol.
This warning status occurs before completing sending data for one page in
some cases, however continuing to send the data prints only one sheet.
Band data of the page for multi-copying has not been saved for one page
completely.
This warning is cleared by the ResetFlag command of the ESCPAGES-02
protocol.
This warning status occurs before completing sending data for one page in
some cases, however continuing to send the data prints only one sheet.
Remedy
This warning occurs only at printing operation by a flying start. After
occurrence of this warning, however, data are resent “the number of copies n -
1" times from the printer driver, so that this warning status is not displayed on
the user interface.
This warning occurs only at printing operation by a flying start. After
occurrence of this warning, however, data are resent “the number of copies n -
1" times from the printer driver, so that this warning status is not displayed on
the user interface.
Check Paper Size
Description
The paper size that was actually fed differed from the paper size recognized
by the paper size detected by printer itself.
This warning is cleared by the ResetFlag command of the ESCPAGES-02
protocol.
This warning does not occur when the specified paper size is an undefined
paper size, and when “Size Ignore = ON” is selected.
The paper size that was actually fed differed from the paper size recognized
by the paper size detected by printer itself.
This warning is cleared by the ResetFlag command of the ESCPAGES-02
protocol.
This warning does not occur when the specified paper size is an undefined
paper size, and when “Size Ignore = ON” is selected.
NOTE 1:
The warning does not occur in the following situation:.
The printer is shared by some PCs and printer changes the control PC
before occurrence of warning on the previous PC.
The printer is shared by some PCs and printer changes the control PC
before occurrence of warning on the previous PC.
2:
Regarding the following envelopes, the paper size for this check is
extended by 5 cm as the flap:
Yokei0, Yokei4, Yokei6, Yokei 3, Chokei4, Chokei3, MON, C10, DL, C5,
C6, IB5
extended by 5 cm as the flap:
Yokei0, Yokei4, Yokei6, Yokei 3, Chokei4, Chokei3, MON, C10, DL, C5,
C6, IB5
Remedy
Clicking the [Close] button closes the pop-up display of the EPSON Status
Monitor. However, if an error of higher priority occurs just after that, the
display changes to the error display. From this point the status is never
displayed until it occurs again.
Clicking the [Close] button closes the pop-up display of the EPSON Status
Monitor. However, if an error of higher priority occurs just after that, the
display changes to the error display. From this point the status is never
displayed until it occurs again.
Print Failure
Description
This warning appears when “Auto Continue=ON” and any of the following
conditions has occurred in the printer.
This warning appears when “Auto Continue=ON” and any of the following
conditions has occurred in the printer.
•
Memory Overflow
•
Printer could not printout a page due to Print Underrun
This warning is cleared by the ResetFlag command of the ESCPAGES-02
protocol.
protocol.
Remedy
Clicking the [Close] button closes the pop-up display of the EPSON Status
Monitor. However, if an error of higher priority occurs just after that, the
display changes to the error display. From this point the status is never
displayed until it occurs again.
Clicking the [Close] button closes the pop-up display of the EPSON Status
Monitor. However, if an error of higher priority occurs just after that, the
display changes to the error display. From this point the status is never
displayed until it occurs again.
NOTE:
Check Paper Size
The warning does not occur in the following situation:.
The printer is shared by some PCs and printer changes the control
PC before occurrence of warning on the previous PC.
The warning does not occur in the following situation:.
The printer is shared by some PCs and printer changes the control
PC before occurrence of warning on the previous PC.
Toner Low
Description
Toner Cartridge life counter is 10% or less of 3000-sheet capacity Developer
Cartridge.
It occurs even if the level is 0% in case of the Toner Out Error = Continue.
Toner Cartridge life counter is 10% or less of 3000-sheet capacity Developer
Cartridge.
It occurs even if the level is 0% in case of the Toner Out Error = Continue.
Remedy
Clicking the [Close] button once closes the pop-up display of the EPSON
Status Monitor. However, it will be displayed again if the warning is still
remain after changing another status.
Clicking the [Close] button once closes the pop-up display of the EPSON
Status Monitor. However, it will be displayed again if the warning is still
remain after changing another status.