Extron electronic 60-1043-12 Merkblatt

1

XTP T HDMI and XTP R HDMI • Setup Guide

This guide provides instructions for an experienced installer to install and connect the Extron XTP T HDMI transmitter and XTP R HDMI receiver.

Transmitter Connections

Receiver Connections

a 

DC power connector 

b 

HDMI input connector

c 

HDMI Loop-thru connector

d 

Analog audio input connector

e 

RS-232/IR Over XTP  

       connector

f 

XTP output connector 

g 

LAN connector

h 

DC power connector 

i 

XTP input connector 

j 

LAN connector 

k 

RS-232/IR Over XTP connector 

l 

HDMI output connector

m 

Analog audio output connector 

n 

S/PDIF audio output connector 

o 

Relay connectors

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required.

Step 2 — Connecting inputs

a. 

Connect a digital video source to the female HDMI connector of the XTP T HDMI (see 

b

 above). It can accept HDMI, DVI (with an 

appropriate adapter), or DisplayPort video signals.

NOTES: 

• 

Use an Extron LockIt

®

 Locking Bracket to secure HDMI cables to the connectors.

• 

Video input from a DisplayPort source must be a dual mode DisplayPort source.

b. 

Connect a digital video display to the HDMI loop-thru connector on the transmitter to locally display the input source. Displays that are not 
HDCP compliant display a green screen when HDCP encrypted content is sent to them (see 

c

 above).

c. 

Connect balanced or unbalanced stereo audio to the  
3.5 mm, 5-pole captive screw connector (see 

d

 

above). 

Step 3 — Connecting Throughput Devices

a. 

Connect a twisted pair cable between the XTP connectors on 
the transmitter and receiver (see 

f

 and 

i

 above).

ATTENTION: 

Do not connect these connectors to a computer data or telecommunications 

network.

The XTP T HDMI and XTP R HDMI are compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair 
(F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Extron recommends using 
the following practices to achieve full transmission distances up to 330 feet (100 m) and reduce 
transmission errors.

 

z

Use Extron XTP DTP 24 SF/UTP cable for the best performance. If not using XTP DTP 24 
cable, at a minimum, Extron recommends 23 AWG, solid conductor, STP cable with a minimum 
bandwidth of 400 MHz.

 

z

Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.

 

z

Limit the use of more than two pass-through points, which may include patch points, punch 
down connectors, couplers, and power injectors. If these pass-through points are required, use 
CAT 6 or 6a shielded couplers and punch down connectors.

NOTE: 

When using CAT 5e or CAT 6 cable in bundles or conduits, consider the following:

• 

Do not exceed 40% fill capacity in conduits.

• 

Do not comb the cable for the first 20 m, where cables are straightened, aligned, and secured in tight bundles.

• 

Loosely place cables and limit the use of tie wraps or hook and loop fasteners.

• 

Separate twisted pair cables from AC power cables.

Signal LED — Lights on the transmitter when it is transmitting a video signal or a test pattern. Lights on the receiver when it receives an 
active XTP input signal from the transmitter.
Link LED — Lights yellow when a valid link between an XTP input and output is established.

1

White-orange

2

Orange

3

White-green

4

Blue

5

White-blue

6

Green

7

White-brown

8

Brown

12345678

Insert Twisted

Pair Wires

1

2

3

4

5

6

7

8

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Sleeve

Tip

g

a

b

k

m n

h

i j

f

d

c

o

e

l