Spectralink 1728 Benutzerhandbuch
42
R
EFERENCE
& I
NSTALLATION
M
ANUAL
9.3
PGM DELAY
Section [066] = PGM1, [067] = PGM2, [068] = Global PGM
001 to 255 seconds, 000 = Follows Deactivation Event, Default = 5 seconds
001 to 255 seconds, 000 = Follows Deactivation Event, Default = 5 seconds
Instead of deactivating the PGM on the occurrence of a specific event, the PGM will deactivate after the period
programmed here has elapsed. PGM2 is available on the 1738EX and 1738 only.
programmed here has elapsed. PGM2 is available on the 1738EX and 1738 only.
If a PGM Delay is programmed, the deactivation event can be used as a second activation event.
9.4
PGM NORMAL STATE
Section [126]: Options [4], [5] and [6]
A PGM toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the
system. PGM2 is available on the 1738EX and 1738 only. You can program each PGM output to be normally open
(N.O.) or normally closed (N.C.) by enabling or disabling options [4], [5] and [6] in section [126].
A PGM toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the
system. PGM2 is available on the 1738EX and 1738 only. You can program each PGM output to be normally open
(N.O.) or normally closed (N.C.) by enabling or disabling options [4], [5] and [6] in section [126].
Option [4] OFF = PGM1 Normally Closed (Default)
Option [4] ON = PGM1 Normally Open
Option [4] ON = PGM1 Normally Open
Option [5] OFF = PGM2 Normally Closed (Default)
Option [5] ON = PGM2 Normally Open
Option [5] ON = PGM2 Normally Open
Option [6] OFF = Global PGM Normally Closed (Default)
Option [6] ON = Global PGM Normally Open
Option [6] ON = Global PGM Normally Open
9.5
PGM2 STROBE OPTIONS (1738EX and 1738 Only)
Section [129]: General Options
Option [1] OFF = PGM2 Output is Steady (Default)
Option [1] ON = PGM2 Output is Pulsed (Strobe)
With option [1] enabled, PGM2 will flash on and off whenever activated. Otherwise, it will provide a steady output.
Option [1] OFF = PGM2 Output is Steady (Default)
Option [1] ON = PGM2 Output is Pulsed (Strobe)
With option [1] enabled, PGM2 will flash on and off whenever activated. Otherwise, it will provide a steady output.
Option [2] OFF = Disable PGM2 Pulse When System is Armed (Default)
Option [2] ON = Enable PGM2 Pulse When System is Armed
Whenever the system is armed, PGM2 will flash once every 30 seconds until the system is disarmed.
Option [2] ON = Enable PGM2 Pulse When System is Armed
Whenever the system is armed, PGM2 will flash once every 30 seconds until the system is disarmed.
Option [3] OFF = Disable PGM2 Pulse on Arm/Disarm (Default)
Option [3] ON = Enable PGM2 Pulse on Arm/Disarm Enabled
With this option enabled, PGM2 will flash once to indicate the system has been armed and will flash twice to indicate
that the system has been disarmed.
Option [3] ON = Enable PGM2 Pulse on Arm/Disarm Enabled
With this option enabled, PGM2 will flash once to indicate the system has been armed and will flash twice to indicate
that the system has been disarmed.
9.6
ALARM RELAY OPTIONS (1738EX and 1738 Only)
Section [127]: General Options
Option [7] OFF = Alarm Relay Follows Bell Output (Default)
Option [7] ON = Alarm Relay Follows Global PGM
Option [7] OFF = Alarm Relay Follows Bell Output (Default)
Option [7] ON = Alarm Relay Follows Global PGM
With this option off, the optional Alarm Relay will activate or deactivate whenever the Bell Output activates or
deactivates. With the option on, the Alarm Relay will activate or deactivate whenever Global PGM activates or
deactivates.
deactivates. With the option on, the Alarm Relay will activate or deactivate whenever Global PGM activates or
deactivates.