Multitech MT5634ZBA-V-V92 Benutzerhandbuch

                

Appendix C – Regulatory Compliance 

Multi-Tech Systems, Inc. MT5634ZBA-Series User Guide (S000286G)                

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 

• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Plug the equipment into an outlet on a circuit different from that to which the receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help. 

This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired 
operation. 

– Changes or modifications to this unit not expressly approved by the party responsible for compliance could 

void the user’s authority to operate the equipment. 

1.  This equipment complies with Part 68 of the Federal Communications Commission Rules. On the outside surface of 

this equipment is a label that contains, among other information, the FCC registration number. This information must 
be provided to the telephone company. 

2.  The suitable USOC jack (Universal Service Order Code connecting arrangement) for this equipment is shown below. 

If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown. 

3.  An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to 

be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant.  

4.  The ringer equivalence number (REN) is used to determine the number of devices that may be connected to the 

telephone line. Excessive RENs on the telephone line may result in the device not ringing in response to an 
incoming call. In most, but not all, areas the sum of the RENs should not exceed 5.0. To be certain of the number of 
devices that may be connected to the line, as determined by the total RENs, contact the local telephone company. 

5.  If this equipment causes harm to the telephone network, the telephone company will notify you in advance that 

temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company 
will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you 
believe it is necessary. 

6.  The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect 

the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you 
to make necessary modifications in order to maintain uninterrupted service. 

7.  If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech 

Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is causing harm to 
the telephone network, the telephone company may request you remove the equipment from the network until the 
problem is resolved. 

8.  No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. 

Unauthorized repairs void registration and warranty. 

9.  This equipment should not be used on party lines or coin lines. 
10.  If so required, this equipment is hearing aid compatible. 
11.  Manufacturer: 

Multi-Tech Systems, Inc. 

Trade Name: 

MultiModem ZBA 

Model Number: 

MT5634ZBA 

FCC Registration No: 

AU7USA-24713-M5-E 

Ringer Equivalence: 

0.3B 

Modular Jack (USOC): 

RJ11C or RJ11W (single line) 

Service Center in USA: 

Multi-Tech Systems, Inc.  

 2205 

Woodale 

Drive 

 

Mounds View, MN 55112      U.S.A. 

 

(763) 785-3500   Fax (763) 785-9874